This 6k-Screw is mainly used at the rear part of the horizontal tail fitting.
 

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

These hinges are used to fix the landing gear door of the Arcus, Nimbus-4 and Duo Discus.

The countersunk screws (fuselage side) and countersunk-head rivet and their washers (door side) can be ordered as an option.

The Schempp-Hirth iconic tool!

This item is part of the horizontal tailplane fixation back system of all the modern Schempp-Hirth gliders. The kit provides all the necessary parts to change 1 pin.

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This item is part of the stabilizer fixation of all the modern Schempp-Hirth gliders.

It is possible to replace or change it for a bigger pin diameter to compensate the ageing of the parts on the stabilizer.

This item is delivered with 4 allen screw M06x30 - 8.8, DIN 912 / ISO 4762 galvanized (L01-0119) and 4 Schnorr-safety washer M6 (L01-0378).

This washer is used for the tail ballast dump valve of most of the Schempp-Hirth gliders.

This 6k-screw is used for the elevator drive U-bracket.
 

This skid is 164 x 48 x 36 mm is used for the Discus-2a, -2b and 2-c.

Double face tape is already fixed on the skid to instal it easily.

These cup washers are used for the bucket seat.

It is size M6 and its dimensions are 13 x 13 x 3 mm.

Tip: For a nicer finish, use these M6 washers with M5 screws (See suggested products).

Nicopress-Stop sleeve 2,5 mm, NTG282G-100.

It is 10 x 9 x 6 mm.

Nicopress-oval sleeve 1,5-2 mm, ref : NT281C-A or N° 28-1-C.

It is 10 x 6 x 4 mm.

This handle is made of plastic. It is 75 mm long and its diameter is 25 mm.

It is used for the airbrake handle of almost all Schempp-Hirth gliders.

This label is made for Discus-2c

This part can be adapted to fit the Duo Discus, Duo Discus X, Duo Discus XL, as well as the Arcus, Arcus Edition 2020, and Nimbus-4D.

It measures approximately 147 mm in width and 157 mm in length.

Please note that the part is sold in an untrimmed form, so you will need to cut it to ensure a proper fit for your glider.

This part can be adapted to fit the Discus-2a, Discus-2b, Discus-2c, Ventus-2ax, Ventus-2bx, the ventus-2c, the ventus-2cx and the Ventus-3.

It measures 148 mm in width. 

Please note that you will need to cut the part to ensure it fits your glider, as it is sold in an untrimmed form.

This cable is designed for the front seat of the Arcus, Duo Discus x, and Duo Discus xL equipped with a TOST wheel and a Magura cylinder brake.

The brake cable is 600 mm long, with a diameter of Ø1.5 mm, and is fitted with a 9 mm diameter nipple.

Please note, this cable is not compatible with the first-generation Duo Discus or the Arcus edition 2020, which are equipped, respectively, with master cylinder model 7 / brakes 30-9 and the BZT2 TOST brake system.

The EASA Form one is included.

This comprehensive kit ensures compatibility with all single-seater gliders equipped with drum brakes and provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 1600 mm of 2 mm cable with a 5.5 x 10 mm nipple
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST, with a “Magura” cylinder brake.

The brake cable measures 555 mm in length and features a 6 x 10 mm nipple.

 

 

These three brass bushes are used for the propellor stopper of the Ventus-3M and the Arcus M edition 2020. The bush in the centre is 8 x 1 x 9.3 mm and the two on the side are 8 x 1 x 6.7 mm.

They can be damaged by the spring and this creates some play in the stopper.

 

This butterfly nut is M10 (DIN 315) and it is used to secure the cockpit weights in all Schempp-Hirth single seaters (except the Ventus-3), the Nimbus, the Janus and some of the first Duo Discus.

This safety pin (or Fokker pin) is 1,5 mm and it is used to secure the cockpit weight in Schempp-Hirth gliders.

This O-ring  Ø32 x Ø3 is used for the water dump valve of several gliders:

• the Duo Discus x and xL,
• all the Arcus,
• some Discus-2c (the system has been upgraded in 2005),
• the Ventus-2cx and the Ventus-2cxa for the inner wing dump system not the outer wing.

This set of gasket can replace the on the main brake cylinder form 6 or 7. It is very likely that this type of cylinder is installed in the Duo Discus (but not in the x or xL), some Nimbus-4(D), as well as in some retrofitted Nimbus and Janus.

It do not work with the rectangular brake cylinder installed on some gliders (Ref: B40-1014). 

This knurled nut M10 DIN 467 is used to secure the cockpit weights of all the Ventus-3, the Arcus and some Duo Discus (xL).

It is sold with the safety pin (L01-0142)

This coupling is used for the fuel line going to the wing tank of the Ventus-3M and the Arcus M.

Please make sure you are entitled and have the skills to change that part. It should be secured with Loctite 577.

Please note: The coupling for the vent line is different. 

This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.

Its stopnut is included.

This is the castle nut is used for the main landing gear of all the Duo Discus and Arcus.

It is 8 mm, M14 x 1,5 DIN 937.

This lid is used for the cooler of all the Ventus-3M (Solo 2625-01i and 2625-01i neo) and all the Arcus M (Solo 2625-02i) but not for the other version. 

This item will allow you to replace the wing fuel tank of your Ventus-2cM and Ventus-2cxM.

 

This threaded rod is M8 and 186mm long.

It is use for the trim of the Duo Discus, Duo Discus xL, Arcus, Nimbus-4D and Nimbus-4DL. The system on the Arcus edition 2020 is different.

This bold is 6h11x28 mm, DIN 1434 / ISO 22341 and galvanized.

It is at the level of the pilot stick both front and back in the Duo Discus and the Nimbus-4D. With time, it can get rusty. 

It is sold here with its splint: 1,6 x 16, DIN 94 / ISO 1234 galvanized.

This washer is  16 x 2 x 5,5 mm and it is used for the tail wheel. 

These springs are uses for the BWS flexiwiper. 

We sell them as a pair to replace the top and bottom springs of one Flexiwiper.

This retrieval Line Dyneema is coated and talc-powdered.

The roll contain 25 m.

5 meter cleaning fialment are also provided !

The deflection pulley is used to eliminate friction from the Bowden cables (in mosquito cleaner systems) in the event of major directional changes of the cable to enable lower manual force/power consumption and faster cleaning.

The mounting plate 4 is specifically designed for the winch to be installed near the back seat pilot feet on the left side.

Please look carefully at the picture.

If you prefer to install it on the right side, you will need the mounting plate Nr. 3.

From wing root to wing tip: The patented joint system adapts to the profile of the glider type during the cleaning process.

At a glance:

• A bug wiper for all types of glider.
• Aerodynamic shape.
• Streamlined, therefore minimum resistance.
• Fiber reinforced plastics with high strength.
• No buckling and no twisting of the components.
• UV-resistant.
• Double guided cleaning fialments: cleans efficiently and glides stably.
• Rests against the profile above and below the wings during the cleaning process.
• Fast mounting.

The BWS Flexiwiper can be retrofitted to almost any glider. For all Schempp-Hirth gliders, the retrival line is routed below the wing. Only this option is available in this shop. Before ordering for another type of glider, you have to consider whether the retrieval line is routed above or below the wing.

The package includes:

• 1 left and 1 right bug wiper inclusive fialments.
• 2 x tilt bracket to fit the fuselage.
• Installation manual.

You can find spare parts and related item below.

This system is fast, reliable and easy to install in your glider. 

The main features are:

• Short cleaning time of approx. 15 seconds per wing (even at high speeds).
• Simultaneous cleaning with both bug wipers possible.
• Three safety features: rope tension sensor, slip clutch and automatic shutdown on overload.
• Tear-resistant Dyneema line (retrieval line).
• Span adjustment (optionnal, please contact us).
• It is sold here with the mounting type 1, the most versatil one. However, if you want to install the winch near the feet of the backseat pilot, you may want to look also to the mounting plate Nr. 3 and Nr. 4.

It is delivered with:

• 2 x BWS electric winches in the box
• 2 x mounting plate no. 1
• 2 x Double switch for instrument panel mounting
• Installation kit double seater
• Installation and operating manuals

You can find spare parts, other mounting plates and related items below.

This system is fast, reliable and easy to install in your glider. 

The main features are:

• Short cleaning time of approx. 15 seconds per wing (even at high speeds).
• Simultaneous cleaning with both bug wipers possible.
• Three safety features: rope tension sensor, slip clutch and automatic shutdown on overload.
• Tear-resistant Dyneema line (retrieval line).
• Span adjustment (optional, please contact us).
• It is sold here with the mounting type 1, the most versatil one, but a large variety of plates are available for easy and flexible installation.

It is delivered with:

• 2 x BWS electric winches in the box
• 2 x mounting plate no. 1 - Suitable for almost all aircraft and installation positions. Special mounting slides (e.g. for Arcus) are also available.
• Double switch for instrument panel mounting
• Installation kit single seater
• Installation and operating manual

You can find spare parts, other mounting plates and related items below.

The simple and proven solution for your bug wriper.

With its integrated damping system, it offers a smooth-run.

It is delivered with:

• 2 pieces BWS crank handles
• Mounting plate
• Installation kit
• Installation and operating manuals

You can find spare parts and related item below.