This copper seal ring is 10 x 14 x 1,5 , DIN 7603 Form A. 

It is used for the fuel line in the Arcus M and the Ventus-3M. 

It is also used for the brakes system Tost - Magura that you might have on the Discus-2b, -2c and Ventus-2c.

This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

This fuel filter Karcoma 99.106/8-100 is used for the refuelling and fuel hoses.

It is 80 mm long and its diameter is 30 mm.

This spark plug is used for all SOLO engines.

This bushing is Ø16x3x24,1.

It is used for the engine bearing of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM

This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.

Its stopnut is included.

This plug is used for the Ventus-3M and the Arcus M Edition 2020.

This bushing is Ø13x1,5x34,5.

It is used for the rear spindle suspension of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM

This sealing is used for the cooling system on the cylinder head of all SOLO 2625 engines.

It is 51 x 32 x 1,5 mm.

Older 2625 engines need another type of filter. If the filter you want to replace doesn't look like that one and is not in metal, contact Schempp-Hirth spare-part service.

This hose NW 4,8x1,6 mm is transparent and it is use for the Fuel sytem.

It is sold my the meter.

These three brass bushes are used for the propellor stopper of the Ventus-3M and the Arcus M edition 2020. The bush in the centre is 8 x 1 x 9.3 mm and the two on the side are 8 x 1 x 6.7 mm.

They can be damaged by the spring and this creates some play in the stopper.

 

Gasket exhaust is used for the SOLO engines 2625.

It is 68,5 x 48 x 2 mm.

It is sold by the unit.

This screw is M10 x 58.

It is used for the rear spindle suspension of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM

This propeller brake pad is designed for the propellers of the almost all the Ventus-2cM, Ventus-3M, and all Arcus M models.

Some Nimbus-4M and Nimbus-4DM gliders may also be equipped with this system if Technical Note 868-19 has been applied.

This rubber element is part of the spindelsuspension of the Ventus-2cM, Ventus-3M, Nimbus-4M, -4DM and Arcus M.

It is 34 mm long.

Depending on the equipment available to you, it might be easier to buy the complete part (B40-13772). See suggested products.

This gummi piece is used to connect the spark plug in the SOLO 2625 and 2350 engines.

SOLO spare part n° 23 00 701 V1

This part used to be black. The old model is no longer available and it is replaced by this new reference.

This sensor is used in the Solo 2625 01i and 2625 02i engines to measure water temperature.

Please note that the sensor used in the older Solo 2625 model is different. You can find it under the suggested products.

This coupling is used for the fuel line going to the wing tank of the Ventus-3M and the Arcus M.

Please make sure you are entitled and have the skills to change that part. It should be secured with Loctite 577.

Please note: The coupling for the vent line is different. 

This rubber element is use for the engine mount of the Arcus M, the Ventus-3M, Ventus-2cM, the Ventus-2cxM, the Nimbus-4M and the Nimbus-4DM.

Its old reference is VW 431407181D.

 

These filters (reference 6064-0A / 0 450 905 401 and E230204) are used for the fuel system of the Ventus-3M.