Controls
-
Spring for rudder pedal adjustment
On the Nimbus-4, the Ventus, the Discus and the Duo Discus the mecanism used to included a spring. It is now replace by a gummi band.
With the kit B40-3235, you can upgrade the old sytem to the newest one.
from 1 € 0.00 incl. 19% VAT
€ 0.00 -
Nicopress-oval sleeve 1,5-2 mm
Nicopress-oval sleeve 1,5-2 mm, ref : NT281C-A or N° 28-1-C.
It is 10 x 6 x 4 mm.
from 1 € 0.21 incl. 19% VAT
€ 0.18 -
Washer Ø4,3xØ20x1,25 DIN 522 for the fin tank dump valve
This washer is used for the tail ballast dump valve of most of the Schempp-Hirth gliders.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
washer 6,4, DIN 9021 / ISO 7093-1 galvanized
This washer is mainly used on the rear part of the horizontal tail fitting.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Copper seal ring
This copper seal ring is 10 x 14 x 1,5 , DIN 7603 Form A.
It is used for the fuel line in the Arcus M and the Ventus-3M.
It is also used for the brakes system Tost - Magura that you might have on the Discus-2b, -2c and Ventus-2c.
from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Thimble 2,5 mm galvanized
Thimble 2,5 mm galvanized.
It is 27 x 15 x 5 mm.
from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Hexagon Screw M06x18 - 8.8, DIN 933 / ISO 4017
This 6k-Screw is used for the elevator drive U-bracket.from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Roll pin for aileron
These roll pins are used to secure the aileron.
Dimension: 2 x 10 mm
DIN 1481 / ISO 8752
from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Roll pin for trim
Roll pin DIN 1481 / ISO 8752 stainless.
They are (mainly) used to in trim of the Arcus, Duo Discus XL and Nimbus-4DL.
There is two models : On gliders produced after April 2015, you will probably need the 2 x 16 mm model. For the older glider you will need to use the 2x14 mm roll pins. Please have a look in your glider to confirm which models you need.
from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Schnorr-safety washer
Safety washers Form S available in M6 and M8.
These washers are used, among other things, to secure the rear part of the horizontal tail fitting and the elevator drive U-bracket.
from 1 € 0.48 incl. 19% VAT
€ 0.40 -
Nicopress-Stop sleeve 1,5-1,7mm
Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).
It is 5 x 5 x 5 mm.from 1 € 0.48 incl. 19% VAT
€ 0.40 -
Blue handgrip for airbrake handle
This handle is made of plastic. It is 75 mm long and its diameter is 25 mm.
It is used for the airbrake handle of almost all Schempp-Hirth gliders.
from 1 € 0.51 incl. 19% VAT
€ 0.43 -
O-ring Ø32 x Ø3 for water dump system of the Duo Discus xL, the Arcus, the Discus-2c and the Ventus-2cx
This O-ring Ø32 x Ø3 is used for the water dump valve of several gliders:
- the Duo Discus x and xL,
- all the Arcus,
- some Discus-2c (the system has been upgraded in 2005),
- the Ventus-2cx and the Ventus-2cxa for the inner wing dump system not the outer wing.
from 1 € 0.55 incl. 19% VAT
€ 0.46 -
Nicopress-Stop sleeve 2,5 mm
Nicopress-Stop sleeve 2,5 mm, NTG282G-100.
It is 10 x 9 x 6 mm.
from 1 € 0.67 incl. 19% VAT
€ 0.56 -
Rubber washer 19x3 mm for the fin tank dump valve
This rubber washer ensures the sealing of the tail ballast of most of the Schempp-Hirth gliders.
It is advisable to replace it every 4-6 years to avoid water leaks.from 1 € 0.82 incl. 19% VAT
€ 0.69 -
Splint bolt for the Duo Discus and Nimbus-4D brake handles
This bold is 6h11x28 mm, DIN 1434 / ISO 22341 and galvanized.
It is at the level of the pilot stick both front and back in the Duo Discus and the Nimbus-4D. With time, it can get rusty.
It is sold here with its splint: 1,6 x 16, DIN 94 / ISO 1234 galvanized.
from 1 € 0.83 incl. 19% VAT
€ 0.70 -
Thimble 3,5 mm galvanized
Thimble 3,5 mm galvanized.
It is 32 x 17 x 6 mm.
from 1 € 0.94 incl. 19% VAT
€ 0.79 -
Black grip
This handle is used for the landing gear grip of all moderne single seaters (except Ventus-3). It is also the flap grip for the first Arcus and for the Ventus b and c. For those two latest, it must be adapted, by cutting a few centimeters of it.
It is 99 mm long and 24 mm at the largest.
from 1 € 1.02 incl. 19% VAT
€ 0.86 -
Nicopress-Stop sleeve 3,0-3,5 mm
Nicopress-Stop sleeve 3,0-3,5 mm, NT283M / n° 28-3-M.
It is 14 x 12 x 8 mm.
from 1 € 1.04 incl. 19% VAT
€ 0.87 -
Hexagon Screw 06036, LN 9037
This 6k-screw is used for the elevator drive U-bracket.
from 1 € 1.71 incl. 19% VAT
€ 1.44 -
Allen screw M06x21 - 8.8, DIN 912 galvanized
This screw is mainly used to secure the rear part of the horizontal tail fitting.from 1 € 3.20 incl. 19% VAT
€ 2.69
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.