This gummi piece is used to connect the spark plug in the SOLO 2625 and 2350 engines.

SOLO spare part n° 23 00 701 V1

This part was originally black, then changed to red, and has now been superseded by this new reference.

This bracket is designed for the battery holders installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The full box is available in the suggested products section at the bottom of the page.

This tension spring (ref. S-4640) is used in the turbo box of the Arcus T, Arcus T edition 2020, Duo Discus T, and Duo Discus xLT.

It is used in the trim system of the Arcus, Duo Discus, Nimbus-4, and Nimbus-4D gliders, in the rear position, with two springs installed per glider.

This galvanized tension spring (type RZ-069) is used for the turbo compartment doors on the Arcus T, Duo Discus T, Discus-2T, Ventus-2cT, Ventus-2cxT and Ventus-3T Performance models.

This MPX-PIK male cable (cross-section 2.5 mm², length 30 cm) connects the most of the modern glider’s electrical system to a battery equipped with an MPX female connector.

The clamp is suitable for hoses with diameters ranging from 12 mm to 20 mm. It is specifically used in the fuel system of the Arcus M and Arcus T.

The clamp is suitable for hoses with diameters ranging from 12 mm to 18 mm and is used on some gliders for the water ballast system in the wing.

This pushrod guide ball cage measures 29 × 3 × 20 mm.

Please note that another model exists with dimensions 25 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This pushrod guide ball cage measures 25 × 3 × 20 mm.

Please note that another model exists with dimensions 29 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This pulley with 626-ZZ bearing is used for the hook release mechanism and for some turbo actuation systems.

This Elesa knurled head screw (M6x16) is used for various functions, including the adjustment mechanism of the headset position.

This indexing plunger without lock is used for the adjustment mechanism of the headset position in all Arcus M models, and for the oxygen bottle mount in the Arcus Edition 2020 and Ventus-3.

This Trim weight is 3,7 kg and it is used for the Arcus, Duo Discus and Janus.

This Polyflex brake hose fit the classic Duo Discus equipped with a master cylinder model 7 / brakes 30-9. 

It is 600 mm lenght.

This foil sealing ring has a diameter of 95 mm and is used to cover the handhole cap of the Duo Discus, Arcus, Discus-2b, Discus-2c, Discus b, Discus cs und Ventus-3 and Ventus-3.

This WK 21 filter is used for the pitot tube in the glider’s nose.

Ring tongue terminal with closed barrel

• Stud size: M6 (≈ 6.73 mm)
• Wire range: 14 AWG (≈ 2 mm²)
• Insulation: Blue, partially insulated sleeve

Applications:

• Electrical power systems
• Ground connection on the wing fuel tank
• Ground connection on the nose

Stainless steel fork head (clevis) with a 4 mm pin diameter and a 16 mm fork width, manufactured in accordance with DIN 71752.

It is used in the fuel actuation system of the Duo Discus T, Duo Discus xT, Duo Discus xLT, Arcus T, Arcus 20 T, Arcus 20 M, and Ventus-3M Neo.

These eyelet is used for the landing gear doors for all models.

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.

Polyflex-hose is 1004 CK and it is 1080mm.