This system is fast, reliable and easy to install in your glider. 

The main features are:

• Short cleaning time of approx. 15 seconds per wing (even at high speeds).
• Simultaneous cleaning with both bug wipers possible.
• Three safety features: rope tension sensor, slip clutch and automatic shutdown on overload.
• Tear-resistant Dyneema line (retrieval line).
• Span adjustment (optionnal, please contact us).
• It is sold here with the mounting type 1, the most versatil one. However, if you want to install the winch near the feet of the backseat pilot, you may want to look also to the mounting plate Nr. 3 and Nr. 4.

It is delivered with:

• 2 x BWS electric winches in the box
• 2 x mounting plate no. 1
• 2 x Double switch for instrument panel mounting
• Installation kit double seater
• Installation and operating manuals

You can find spare parts, other mounting plates and related items below.

This system is fast, reliable and easy to install in your glider. 

The main features are:

• Short cleaning time of approx. 15 seconds per wing (even at high speeds).
• Simultaneous cleaning with both bug wipers possible.
• Three safety features: rope tension sensor, slip clutch and automatic shutdown on overload.
• Tear-resistant Dyneema line (retrieval line).
• Span adjustment (optional, please contact us).
• It is sold here with the mounting type 1, the most versatil one, but a large variety of plates are available for easy and flexible installation.

It is delivered with:

• 2 x BWS electric winches in the box
• 2 x mounting plate no. 1 - Suitable for almost all aircraft and installation positions. Special mounting slides (e.g. for Arcus) are also available.
• Double switch for instrument panel mounting
• Installation kit single seater
• Installation and operating manual

You can find spare parts, other mounting plates and related items below.

The simple and proven solution for your bug wriper.

With its integrated damping system, it offers a smooth-run.

It is delivered with:

• 2 pieces BWS crank handles
• Mounting plate
• Installation kit
• Installation and operating manuals

You can find spare parts and related item below.

This instrument panel is sold raw. It would fit the Discus b, Ventus b and Ventus c. You can order it with or without an extra space for the knees.

 

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.

This microphone is adapted to radio with electret input.

Mounting kit is included in the price.

This battery holders is installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The metalic bracket is available in the suggested products section at the bottom of the page.

This threaded rod is M8 and 186mm long.

It is use for the trim of the Duo Discus, Duo Discus xL, Arcus, Nimbus-4D and Nimbus-4DL. The system on the Arcus edition 2020 is different.

This oxygen bottle holder is suitable for a majority of gliders equiped with a turbo or a motor.

Please choose which holder you need according to your Oxygen-bottle diameter.  It is possible to adjust the holder at +/- 2 mm.

In single-seaters, one of the screws of the support is often above the spar bridge, where the wall is relatively thin. It is therefore often necessary to add the washer B40-2218 (see suggested products).

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.

Polyflex-hose is 1004 CK and it is 1080mm.

This microphone is adapted for radio with dynamic input.

It is delivered with the nut and the safety lock.

You can add the Schempp-Hirth microphone mounting as an option.

This bracket is designed for the battery holders installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The full box is available in the suggested products section at the bottom of the page.

This part is used for the notching of the flaps of the Ventus-2b.

It is 135 mm long and the screw holes are spaced 50 and 69 mm apart respectively.

This part is used for the notching of the flaps of the Ventus c.

It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.

This part is used for the notching of the flaps of the Ventus-2bx, Ventus-2c and Ventus-2cx.

It is 146 mm long and the screw holes are spaced 50 and 69 mm apart respectively.