This battery holders is installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The metalic bracket is available in the suggested products section at the bottom of the page.

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.

This microphone is adapted to radio with electret input.

Mounting kit is included in the price.

This threaded rod is M8 and 186mm long.

It is use for the trim of the Duo Discus, Duo Discus xL, Arcus, Nimbus-4D and Nimbus-4DL. The system on the Arcus edition 2020 is different.

This oxygen bottle holder is suitable for a majority of gliders equiped with a turbo or a motor.

Please choose which holder you need according to your Oxygen-bottle diameter.  It is possible to adjust the holder at +/- 2 mm.

In single-seaters, one of the screws of the support is often above the spar bridge, where the wall is relatively thin. It is therefore often necessary to add the washer B40-2218 (see suggested products).

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.

Polyflex-hose is 1004 CK and it is 1080mm.

This support is used on a fuselage side, to fixe the rear headrest. 

It is composed of the headrest holder, the locking plate, the 7.2mm bolt and the part that connect to the fuselage.

 

This bracket is designed for the battery holders installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The full box is available in the suggested products section at the bottom of the page.

This part is used for the notching of the flaps of the Ventus-2b.

It is 135 mm long and the screw holes are spaced 50 and 69 mm apart respectively.

This part is used for the notching of the flaps of the Ventus c.

It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.

This part is used for the notching of the flaps of the Ventus-2bx, Ventus-2c and Ventus-2cx.

It is 146 mm long and the screw holes are spaced 50 and 69 mm apart respectively.

This Trim weight is 3,7 kg and it is used for the Arcus, Duo Discus and Janus.

This is the handle for the trim of the Arcus, Duo Discus XL and Nimbus-4DL.

The roll pins are included. 

Please note the pin roll can be bought separatly (see suggested product). If your glider is older than April 2015, you need to use the 2x14 mm roll pins instead of 2x16 mm.

 

This fabric bag is placed around the pilot stick of the front seat of the double seaters. This model is not adapted for the Arcus edition 2020.

It is a safety feature, preventing things going inside the controls. If it get old or damaged you can replace it.

It is sold without frame.

This kit contains all  you need to replace the pedal adjustment mechanism, including the instructions.

It is made for the Ventus b, Ventus c, Ventus-2, Discus, Discus-2, Nimbus-4, Duo Discus and the Arcus. 

On the Nimbus-4, the Ventus, the Discus and the Duo Discus the mecanisme included a spring. It is now replace by a gummi band. With this kit, you can upgrade the old sytem to the newest one.

This adapter is necessary for the MH Oxygen bottle. 

Indeed the neck of these bottle is short and wide and, without the extension, the pressure gauge prevents the neck holder from being installed.

This pilot stick handle is made by Air Ergo Leki for the Schempp-Hirth 19,3 mm diameter control sticks.

3 adaptors are provided for the  folowing settings: No SC, SC switch or SC button.

The canopy window rail device including screws. The screws are in metal but as an option, you can order it in plastic.

These rails are made for the Mecaplex canopy. It is the only model currently available, but you may need to customise it a little if you have a Weis canopy.

 

This tension spring is used to hold the flap handle in the correct position.

It was originally used on the Janus C, Nimbus-3D, and Nimbus-4D, and is located on the rear cockpit wall (back seat).

However, some gliders have been modified and now use a flat spring (Ref. B40-0297) mounted near the spar bridge.

The temperature-indicator TF-00-059 is compact and readable. It temperatur captor can easily reach the front ventilation with its 125 cm cable.

This thermometer is mandatory for all the Schempp-Hirth gliders with water ballast.

This fiberglass bracket is designed for 7.5 Ah battery holders.

It has a width of 38 mm and fits a 97 mm battery. The shape is straight. 

A similar model (F60-0651) features a bend and is used in several gliders, including the Duo Discus XL and the Arcus. Please check the model installed in your glider carefully before purchasing.

This label is made for the Arcus (Arcus M SN<216 and Arcus T SN<90).

 

These pictograms can be used in Discus-2 and Duo Discus.

This 350 N gas strut is 293 mm long.

It is used for the foldable instrument panel of the Ventus-2c, Ventus-2bx, Discus-2a, Discus-2b and Discus-2c. 

This label is made for Discus-2c

This label is made for the Ventus-3.

 

This 300 N gas strut is 313 mm long.

It is used for the foldable instr. panel of the Discus-2c FES, Discus b, Ventus c and Ventus-2b.

This gas strut is 450 N and 178 mm long.

It is used for the foldable instrument panel of Arcus and Duo Discus XL.

This grey PVC plate is used as a guide for the Duo Discus and Nimbus-4D.

Dimensions: 220 × 25 mm.

Please note: the model used for the Duo Discus XL, Arcus, and Nimbus-4DL is longer (ref. B40-3306). You can find it in the suggested products below.

This label is made for the original Arcus.

 

This pulley with 626-ZZ bearing is used for the hook release mechanism and for some turbo actuation systems.

This tension spring is used to maintain the flap handle on the right position. 

On the Janus B and Nimbus-2, it is located near the front seat handle.

Originally, the Janus C, the Nimbus-3D and the Nimbus-4D are using another spring that looks very different (ref B40-2417) and that is located on the back seat cockpit wall. However some gliders have been modified and they are now using this flat spring but near the spar bridge.

The other reference is available below under the suggested products.

This handle for the trim is a format 25 mm, M6. It is made in aluminium and green powdered.

These eyelet is used for the landing gear doors for all models.

This grey PVC plate is used as a guide for the Duo DiscusxL and xLT and Arcus.

Dimensions: 233×25 mm.

Please note: the model used for the Duo Discus and Nimbus-4D is shorter (ref. B40-3305). You can find it in the suggested products below.

These fuses are used for instruments.

They are available in 2, 4 and 6,3 A.

This gasket is used for the canopy of the Duo Discus and the Arcus.

It is sold by the meter.

This WK 21 filter is used for the pitot tube in the glider’s nose.