This threaded rod is M8 and 186mm long.

It is use for the trim of the Duo Discus, Duo Discus xL, Arcus, Nimbus-4D and Nimbus-4DL. The system on the Arcus edition 2020 is different.

This part is used for the notching of the flaps of the Ventus-2b.

It is 135 mm long and the screw holes are spaced 50 and 69 mm apart respectively.

This part is used for the notching of the flaps of the Ventus c.

It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.

This part is used for the notching of the flaps of the Ventus-2bx, Ventus-2c and Ventus-2cx.

It is 146 mm long and the screw holes are spaced 50 and 69 mm apart respectively.

This is the handle for the trim of the Arcus, Duo Discus XL and Nimbus-4DL.

The roll pins are included. 

Please note the pin roll can be bought separatly (see suggested product). If your glider is older than April 2015, you need to use the 2x14 mm roll pins instead of 2x16 mm.

 

This fabric bag is placed around the pilot stick of the front seat of the double seaters. This model is not adapted for the Arcus edition 2020.

It is a safety feature, preventing things going inside the controls. If it get old or damaged you can replace it.

It is sold without frame.

This kit contains all  you need to replace the pedal adjustment mechanism, including the instructions.

It is made for the Ventus b, Ventus c, Ventus-2, Discus, Discus-2, Nimbus-4, Duo Discus and the Arcus. 

On the Nimbus-4, the Ventus, the Discus and the Duo Discus the mecanisme included a spring. It is now replace by a gummi band. With this kit, you can upgrade the old sytem to the newest one.

This pilot stick handle is made by Air Ergo Leki for the Schempp-Hirth 19,3 mm diameter control sticks.

3 adaptors are provided for the  folowing settings: No SC, SC switch or SC button.

This grey PVC plate is used as a guide for the Duo Discus and Nimbus-4D.

Dimensions: 220 × 25 mm.

Please note: the model used for the Duo Discus XL, Arcus, and Nimbus-4DL is longer (ref. B40-3306). You can find it in the suggested products below.

This handle for the trim is a format 25 mm, M6. It is made in aluminium and green powdered.

This grey PVC plate is used as a guide for the Duo DiscusxL and xLT and Arcus.

Dimensions: 233×25 mm.

Please note: the model used for the Duo Discus and Nimbus-4D is shorter (ref. B40-3305). You can find it in the suggested products below.

This plate in grey PVC is used as a guide for all single-seater landing gear (except for the Ventus-3).

Its length is 220 x 24 mm and there is no hole. Adjust it to your glider.

This spring is used for the trim of the Arcus, Duo Discus XL, Nimbus-4DL and all the Discus from the Discus a to the Discus-2c.

It is 25mm lage and the legs are 40mm long. The central part is 12,5mm.

Some glider need roll pins. They are not included but they can be baught individaly (see the suggested products). 

This tension spring (ref RZ-124) is used in the rudder pedal of the Arcus, Duo Discus, and Nimbus-4D gliders, in the rear position, with two springs installed per glider. It is also used for the doors of the engine box in single seater.

This handle is used for the landing gear grip of all moderne single seaters (except Ventus-3). It is also the flap grip for the first Arcus and for the Ventus b and c. For those two latest,  it must be adapted, by cutting a few centimeters of it.

It is 99 mm long and 24 mm at the largest.

This bold is 6h11x28 mm, DIN 1434 / ISO 22341 and galvanized.

It is at the level of the pilot stick both front and back in the Duo Discus and the Nimbus-4D. With time, it can get rusty. 

It is sold here with its splint: 1,6 x 16, DIN 94 / ISO 1234 galvanized.

This handle is made of plastic. It is 75 mm long and its diameter is 25 mm.

It is used for the airbrake handle of almost all Schempp-Hirth gliders.

Roll pin DIN 1481 / ISO 8752 stainless.

They are (mainly) used to in trim of the Arcus, Duo Discus XL and Nimbus-4DL.

There is two models : On gliders produced after April 2015, you will probably need the 2 x 16 mm model. For the older glider you will need to use the 2x14 mm roll pins. Please have a look in your glider to confirm which models you need.