Tension Spring for the Discus-2 Trim System, Part No.: RZ-123 I

Tension spring for the trim system of the Discus-2 series. 3 springs are required per aircraft.

It is  Ø 1,6 x 14,1 x 59 mm

 

Rod end bearing with a 10c6 head and M8x58 length body.

Other rod end bearings are used in our gliders. If you are not sure which one you need. Please contact the Spare Part team.

This grey PVC plate is used as a guide for the Duo DiscusxL and xLT and Arcus.

Dimensions: 233×25 mm.

Please note: the model used for the Duo Discus and Nimbus-4D is shorter (ref. B40-3305). You can find it in the suggested products below.

This grey PVC plate is used as a guide for the Duo Discus and Nimbus-4D.

Dimensions: 220 × 25 mm.

Please note: the model used for the Duo Discus XL, Arcus, and Nimbus-4DL is longer (ref. B40-3306). You can find it in the suggested products below.

Gasket for the canopy frame of single-seat gliders, sold by the metre.

Please note: some gliders have this gasket on one side only, with a different seal on the other side (the one used for the two-seaters, see recommanded product). Please check your glider carefully before ordering.

This connection fitting is used, sometime, to the Polyflex hose of the classic Duo Discus which are using the Classic wheel from TOST with a Magura cylinder brake.

This support is used on a fuselage side, to fixe the rear headrest. 

It is composed of the headrest holder, the locking plate, the 7.2mm bolt and the part that connect to the fuselage.

 

The tension spring is used for the retraction of the landing gear of all the Discus, Discus-2, Ventus, Ventus-2 and the Nimbus-4.

Its dimensions are 1,6 x 12,7 x 164,5 mm.

This bowden cable is 5,3 x 4,4 x 3,0 mm. It can also be referred to as 5.51.0000.022.

It is 80 cm and includes 2 cable end caps. To order a bigger quantity see the 

This cable is often used for the wheel brake systems. Please refer to your maintenance manual for the type of cable you need and how to make the connections.

 

Protective cover for the main pin made of Supra-Tex. Designed to store and protect the main pin from dirt and damage while the glider is not rigged.

 

These replacement springs are specifically designed for use with the BWS Garagewiper system. Each set is sold as a matched pair for the left and right wiper units.

Important compatibility note:
These springs are not compatible with the classic Flexiwiper model.

This service applies when our team enters an order by phone on the customer’s behalf. It is used only in special cases where personal assistance is required. 

This gummi piece is used to connect the spark plug in the SOLO 2625 and 2350 engines.

SOLO spare part n° 23 00 701 V1

This part was originally black, then changed to red, and has now been superseded by this new reference.

This battery holders is installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The metalic bracket is available in the suggested products section at the bottom of the page.

This bracket is designed for the battery holders installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The full box is available in the suggested products section at the bottom of the page.

This tension spring (ref. S-4640) is used in the turbo box of the Arcus T, Arcus T edition 2020, Duo Discus T, and Duo Discus xLT.

This tension spring (ref RZ-124) is used in the rudder pedal of the Arcus, Duo Discus, and Nimbus-4D gliders, in the rear position, with two springs installed per glider. It is also used for the doors of the engine box in single seater.

It is used in the trim system of the Arcus, Duo Discus, Nimbus-4, and Nimbus-4D gliders, in the rear position, with two springs installed per glider.

This galvanized tension spring (type RZ-069) is used for the turbo compartment doors on the Arcus T, Duo Discus T, Discus-2T, Ventus-2cT, Ventus-2cxT and Ventus-3T Performance models.

This MPX-PIK male cable (cross-section 2.5 mm², length 30 cm) connects the most of the modern glider’s electrical system to a battery equipped with an MPX female connector.

The clamp is suitable for hoses with diameters ranging from 12 mm to 20 mm. It is specifically used in the fuel system of the Arcus M and Arcus T.