This system is fast, reliable and easy to install in your glider. 

The main features are:

• Short cleaning time of approx. 15 seconds per wing (even at high speeds).
• Simultaneous cleaning with both bug wipers possible.
• Three safety features: rope tension sensor, slip clutch and automatic shutdown on overload.
• Tear-resistant Dyneema line (retrieval line).
• Span adjustment (optionnal, please contact us).
• It is sold here with the mounting type 1, the most versatil one. However, if you want to install the winch near the feet of the backseat pilot, you may want to look also to the mounting plate Nr. 3 and Nr. 4.

It is delivered with:

• 2 x BWS electric winches in the box
• 2 x mounting plate no. 1
• 2 x Double switch for instrument panel mounting
• Installation kit double seater
• Installation and operating manuals

You can find spare parts, other mounting plates and related items below.

This system is fast, reliable and easy to install in your glider. 

The main features are:

• Short cleaning time of approx. 15 seconds per wing (even at high speeds).
• Simultaneous cleaning with both bug wipers possible.
• Three safety features: rope tension sensor, slip clutch and automatic shutdown on overload.
• Tear-resistant Dyneema line (retrieval line).
• Span adjustment (optional, please contact us).
• It is sold here with the mounting type 1, the most versatil one, but a large variety of plates are available for easy and flexible installation.

It is delivered with:

• 2 x BWS electric winches in the box
• 2 x mounting plate no. 1 - Suitable for almost all aircraft and installation positions. Special mounting slides (e.g. for Arcus) are also available.
• Double switch for instrument panel mounting
• Installation kit single seater
• Installation and operating manual

You can find spare parts, other mounting plates and related items below.

This item will allow you to replace the wing fuel tank of your Ventus-2cM and Ventus-2cxM.

 

This item will allow you to replace the wing fuel tank of your Arcus.

 

This item is composed of the rim, the tire and the inner tube. It is adapted for the Ventus-3.

This support is used for the lower rudder of the Arcus M.

The EASA Form one is included.

This slip joint is used in the exhaust system of the Solo 2625-01i, 2625-01i Neo, 2625-02i and 2625-02i Neo engines, which are installed in the Ventus-3 and the Arcus gliders.

It is the Solo spare part 25 00 850.

This toothed belt is 2400 mm and is adapted for the Ventus-2cM pylon with a Solo 2625-01 engine.

This water pompe is used for all the SOLO engines 2625.

This wingtip wheel is made for the Ventus-2c.

This system is aerodynamic and compact (212 x 95 x 59 mm). In addition it is weighting only 200 g.

It is sold by the unit.

You can to fix it with screws that are included. Look at look wing tip, the holes are 165 mm apart.

This wingtip wheel is designed for the Arcus. It is aerodynamic but high enough and resistant to drive on the ground.

The item is 236 x 116 x 69 mm and the screws are 165 mm apart.

It sold by the unit and the screws are provided.

 

 

These bug-wipers blades are adapted for all the Ventus-3 variants and the Arcus Edition 2020 with garage for bug-wipers.

The simple and proven solution for your bug wriper.

With its integrated damping system, it offers a smooth-run.

It is delivered with:

• 2 pieces BWS crank handles
• Mounting plate
• Installation kit
• Installation and operating manuals

You can find spare parts and related item below.

This throttle valve sensor mounted (Solo part number 23 00 910) is used in the Solo 2625 01i, Solo 2625 01i Neo and 2625 02i.

 

This 2520 Poly Chain GT2 toothed belt is designed for the pylon of the Nimbus-4M and Nimbus-4DM equipped with a Solo engine 2625.

Solo part: 23 00 781 02

Starter from Denso for Solo engine 2625.