This wingtip wheel is made for the Ventus-2c.

This system is aerodynamic and compact (212 x 95 x 59 mm). In addition it is weighting only 200 g.

It is sold by the unit.

You can to fix it with screws that are included. Look at look wing tip, the holes are 165 mm apart.

This wingtip wheel is designed for the Arcus. It is aerodynamic but high enough and resistant to drive on the ground.

The item is 236 x 116 x 69 mm and the screws are 165 mm apart.

It sold by the unit and the screws are provided.

 

 

These bug-wipers blades are adapted for all the Ventus-3 variants and the Arcus Edition 2020 with garage for bug-wipers.

The Lindner system offers a great compromise between aerodynamic and ease of handling on the ground.

This wingtip wheel is designed for the Duo Discus and the Discus-2c. To install these wheels, your glider need to have the adapted fixation system.

The support, with the wheel, is 211 X 60 x 100 mm and has two holes for screws, that are 165 mm apart.

It is sold by the unit and the screws are included.

 

This drive funnel is used on almost all Schempp-Hirth gliders except the Nimbus-4 and the Ventus-3.

Two lock nuts M 6-8, DIN 985 and a lock nut M6 TRELOC, DIN 439 are included. However, your glider has a specific set of distance washer that are not provided. Please before disassemble the funnel make sure you know which washer go where.

On the Ventus-2 and Discus-2c, you may also need a set of screws that can be baught as an option.

From wing root to wing tip: The patented joint system adapts to the profile of the glider type during the cleaning process.

At a glance:

• A bug wiper for all types of glider.
• Aerodynamic shape.
• Streamlined, therefore minimum resistance.
• Fiber reinforced plastics with high strength.
• No buckling and no twisting of the components.
• UV-resistant.
• Double guided cleaning fialments: cleans efficiently and glides stably.
• Rests against the profile above and below the wings during the cleaning process.
• Fast mounting.

The BWS Flexiwiper can be retrofitted to almost any glider. For all Schempp-Hirth gliders, the retrival line is routed below the wing. Only this option is available in this shop. Before ordering for another type of glider, you have to consider whether the retrieval line is routed above or below the wing.

The package includes:

• 1 left and 1 right bug wiper inclusive fialments.
• 2 x tilt bracket to fit the fuselage.
• Installation manual.

You can find spare parts and related item below.

This 150N gas strut is used for the Mini-Nimbus airbreaks.

 

This 200N gas strut is in the airbrake box. It connects the airbrake rod to the actuating lever of the trailing edge flap for the Duo Discus X and xL as well as the Nimbus-3D, -4 and -4D.

An older version used a gas spring from the company Hahn, you can use this one instead.

This plexi cover is made for the Janus, the Ventus b and some Ventus-2. It is used in the TN 349-42 / 825-57.

Its diameter is 53,5 mm and the central hole is 5 mm. The locking device is 100mm long.

 

This sealing lid is for the Arcus edition 2020.

It is equipped of a non-return valve.

The visible part of the peg is 70,5 mm long with a 14 mm diameter. The internal part is 35 mm long, with a 40 mm diameter.

It is used on the back part of the Discus-2c and Ventus-2c wing roots.

The deflection pulley is used to eliminate friction from the Bowden cables (in mosquito cleaner systems) in the event of major directional changes of the cable to enable lower manual force/power consumption and faster cleaning.

This wingtip wheel is 84 x 84 x 11 mm rim with a 60 x 10 O-Ring NBR70 tyre. It made for the Lindner system wingtip wheels of the Duo Discus, Discus-2c and the Ventus.

It is sold by the unit.

 

This skid is 194 x 47 x 37 mm and is used for all Duo Discus.

Double face tape is already fixed on the skid to make it easy to instal.

The Schempp-Hirth iconic tool with an extra pin to dismantle the wingtip and an extra tool for the ballast plugs.

The visible part of the pin is 38,5 mm long with a 14 mm diameter. The inner part is 35 mm long and has a diameter of 40 mm.

It is used on the wing roots front part of the Discus, Discus-2, Ventus, Ventus-2c and Ventus-3S.

Some slightly older gliders, such as the Discus b, use this part for both the front and the back. Others will have a longer pin at the back. You can find it in the suggested product list. Please check carefully which version your glider uses.

The visible part of the peg is 78,5 mm long and has a diameter of 18 mm. The inner part is 42 mm long and has a diameter of 40 mm.

It is used on the wing roots back part of the Nimbus-3D, the Nimbus-4D, the Duo Discus and the Arcus. It is not adapted for the Janus.

 

The visible part of the pin is 48 mm long and has a diameter of 18 mm. The inner part is 42 mm long and has a diameter of 40 mm.

It is used on the wing roots front part of the double seaters as well as for the front and rear roots of the Janus.

These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.

They fit a 18 mm wing bolt. That includes the front and back bolts at the wing root of the double seaters.

These washers internal diameter is 17,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

 

This skid is 164 x 48 x 36 mm is used for the Discus-2a, -2b and 2-c.

Double face tape is already fixed on the skid to instal it easily.

This skid is 121 x 35 x 28,5 mm and is used for Discus a, Discus b, Ventus b, Ventus c and all the Ventus-2.

Double face tape is already fixed on the skid to instal it easily.

This retrieval Line Dyneema is coated and talc-powdered.

The roll contain 25 m.

5 meter cleaning fialment are also provided !

This spherical bearing is adapted for 14mm diameter pin of the single seaters.

The internal diameter is 14 mm and the part is 25x25x8-11 mm.

 

This sealing cap is made for the Ventus-3 outer wing.

The plug used for the inner wing is different. You can find it below in the suggested items.

Please note that the first seven Ventus-3 are equipped with a different system.

This 300N gas strut is located in the fuselage. It connects to the airbrake drive shaft in the Duo Discus x and xL.

If the airbrakes become very hard to operate, it may be that this gas strut needs to be replaced.

These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.

They fit a 14 mm wing bolt. That includes the front and back bolts at the wing root of almost all the single seaters as well as the wing extention bolt of the Discus-2c, Ventus-2c and Ventus-3 and some winglet bolts.

These washers internal diameter is 13,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

This tool allows you to assemble Discus-2c, Ventus-2c and Ventus-3 wing extensions.

The Schempp-Hirth iconic tool with an extra pin to dismantle the wingtip.

This sealing cap is made for the Ventus-3 inner wing.

The plug used for the outer wing is different. You can find it below in the suggested items.

Please note that the first seven Ventus-3 are equipped with a different system.

This rubber boot is surrounding the water ballast control rod to avoid the water leaking through. It is used in several Schempp-Hirth gliders including the Nimbus-2, Ventus, Ventus-2c, Discus-2c, Duo Discus and the Arcus.

It is 125 x 22 x 22 mm with a 7 mm and a 16 mm opening.

Over the years, other bellows and different combinations have been used. You can find them underneath this description, in the "suggested products", if you want to compare them with the model that you wish to replace.

This flexible rubber boot is 63 x 39x 39 mm with a 10 mm and a 25 mm opening.

It is surrounding the ballast rod on the wing root of the Discus b, Ventus-2 (SN < 561), Discus-2a and Discus-2b (SN< 234) which have been produced before June 2009. However, some of these gliders might have been retrofitted with the newer system. You can see on the suggested product the other bellow.

It is used for the ballast system of the Nimbus-3, -3D, -4 and -4D. For the Nimbus, the bellow may need to be adapted by cutting the larger end.

It is also used as a sealing around the brake line when crossing the wheel box in all single seaters.

 

The clamp is suitable for hoses with diameters ranging from 12 mm to 18 mm and is used on some gliders for the water ballast system in the wing.

These replacement springs are specifically designed for use with the BWS Flexiwiper system. Each set is sold as a matched pair, for the left and right Flexiwiper unit.

Important compatibility note:
These springs are not compatible with the Ventus-3 or Arcus edition 2020 Garagewipers models. 

These replacement springs are specifically designed for use with the BWS Garagewiper system. Each set is sold as a matched pair for the left and right wiper units.

Important compatibility note:
These springs are not compatible with the classic Flexiwiper model.

This wingtip wheel axle is used for the Arcus and Ventus-2c.

The safety ring spring can be found in the suggested products below.

This spherical bearing is adapted for 18mm diameter pin of the double seaters.

The internal diameter is 18 mm and the part is 32x32x14 mm.

This perspex disc is made for the Ventus-2a.

Its diameter is 53,5 mm and the central hole is 5 mm.

Rod end bearing with a 10c6 head and M8x58 length body.

Other rod end bearings are used in our gliders. If you are not sure which one you need. Please contact the Spare Part team.

This pair of leg springs is used for the Arcus, Duo Discus xL and Ventus-2cx.

Each spring is 101,5 mm long and 21 mm large.

This sealing is made for the Ventus-3 sealing caps.

Its diameter is 26 mm and the sealing is 4,0mm thick.

This gummi ring is Ø60 x Ø10 and  is the tire of the wing wheel Lindner of the Duo Discus, Discus and the Ventus.

It is sold by the unit.

 

These washers are 14x9,8x0,5 mm.

They are made for the wing bolt that have a 10 mm diameter. This includes the wing extension bolt of all Arcus, all Duo Discus, the Nimbus-3, -3D, -4 and -4D, the Janus, the Discus-b, the Discus-2a and -2b and the Ventus c. It is also the case for the winglet bolt of the Discus, the Standard Cirrus, the Ventus-2a and the Ventus-2b.

These washers internal diameter is 9,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

They are sold in a kit of 4.