These three brass bushes are used for the propellor stopper of the Ventus-3M and the Arcus M edition 2020. The bush in the centre is 8 x 1 x 9.3 mm and the two on the side are 8 x 1 x 6.7 mm.

They can be damaged by the spring and this creates some play in the stopper.

 

This coupling is used for the fuel line going to the wing tank of the Ventus-3M and the Arcus M.

Please make sure you are entitled and have the skills to change that part. It should be secured with Loctite 577.

Please note: The coupling for the vent line is different. 

This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.

Its stopnut is included.

This lid is used for the cooler of all the Ventus-3M (Solo 2625-01i and 2625-01i neo) and all the Arcus M (Solo 2625-02i) but not for the other version. 

This item will allow you to replace the wing fuel tank of your Ventus-2cM and Ventus-2cxM.

 

This item will allow you to replace the wing fuel tank of your Arcus.

 

This copper seal ring is 10 x 14 x 1,5 , DIN 7603 Form A. 

It is used for the fuel line in the Arcus M and the Ventus-3M. 

It is also used for the brakes system Tost - Magura that you might have on the Discus-2b, -2c and Ventus-2c.

This plug is used for the Ventus-3M and the Arcus M Edition 2020.

This bushing is Ø16x3x24,1.

It is used for the engine bearing of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM

These filters (1 filter Pierburg 4.00030.80.0 and 1 filter KL14 Mahle) are used for the fuel system of the Arcus M.

This rubber element is use for the engine mount of the Arcus M, the Ventus-3M, Ventus-2cM, the Ventus-2cxM, the Nimbus-4M and the Nimbus-4DM.

Its old reference is VW 431407181D.

 

This pneumatic spring is 820 mm long. It is used for the Duo Discus T, Duo Discus xT, Duo Discus xLT, the Arcus T and Arcus T edition 2020.

This part is used for the Discus bM, the Ventus-2cM, the Ventus-3M, the Nimbus-4DM and the Arcus M.

This screw is M10 x 58.

It is used for the rear spindle suspension of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM

This bushing is Ø13x1,5x34,5.

It is used for the rear spindle suspension of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM

This air filter RC-1060 (Solo ref: 25 00 845) is used for the 2625-02i.

It used to be rectangular but the shape changed. You can use this model instead of the square ones.

This item is 1 set of 5 pieces.

SOLO spare-part n° 00 57 225

 

This gas strut is 500N and it is used for the engine mount of the Ventus T, Discus T, Ventus cM, the Nimbus-3T and the Nimbus-4T.

More modern single seaters are using the reference L03-0122, that is 600N. You can find it on the suggested product.

This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

This rubber element is part of the spindelsuspension of the Ventus-2cM, Ventus-3M, Nimbus-4M, -4DM and Arcus M.

It is 34 mm long.

Depending on the equipment available to you, it might be easier to buy the complete part (B40-13772). See suggested products.

This ignition cable is 35 cm long and it is used for the Arcus M.

You will need 4 units. if you want to change all of them.

This proximity switch (ref  IX02 0815) is used for the automatic propeller brake in the Arcus M. 

It is not addapted to the Arcus M edition 2020.

This position sensor is sold as a unit (you might need two of them) and the FUT plug is included.

 

These filters (reference 6064-0A / 0 450 905 401 and E230204) are used for the fuel system of the Ventus-3M.

This toothed belt is 2400 mm and is adapted for the Ventus-2cM pylon with a Solo 2625-01 engine.

This water pompe is used for all the SOLO engines 2625.

Gasket exhaust is used for the SOLO engines 2625.

It is 68,5 x 48 x 2 mm.

It is sold by the unit.

This spark plug is used for all SOLO engines.

This sealing is used for the cooling system on the cylinder head of all SOLO 2625 engines.

It is 51 x 32 x 1,5 mm.

Older 2625 engines need another type of filter. If the filter you want to replace doesn't look like that one and is not in metal, contact Schempp-Hirth spare-part service.

This fuel filter Karcoma 99.106/8-100 is used for the refuelling and fuel hoses.

It is 80 mm long and its diameter is 30 mm.

Two models exist, with or without a base, please choose the model who is already on your glider.

They are 10 mm high.

They are sold individually but you will need 5 of them for your glider.

This gummi piece is used to connect the spark plug in the SOLO 2625 and 2350 engines.

SOLO spare part n° 23 00 701 V1

This part used to be black. The old model is no longer available and it is replaced by this new reference.

SOLO Silent block bush, spare part n° 00 94 240

It is 14 mm large and its diameter is 37 mm.

This item is 1 set of 5 pieces.

SOLO spare-part n° 00 57 224

 

This hose NW 4,8x1,6 mm is transparent and it is use for the Fuel sytem.

It is sold my the meter.

The kit contains the cable (diameter 3,2 mm), 2 nicopress-oval sleeves, 2 thimbles and some silicone tube. One side is already assembled.

It can be use for the Ventus-2cM, Ventus-3M, the Nimbus-4M and -4DM and the Arcus M.

Please refer to the maintenance manual for the installation.