This item will allow you to replace the wing fuel tank of your Arcus.

 

This item will allow you to replace the wing fuel tank of your Ventus-2cM and Ventus-2cxM.

 

This slip joint is used in the exhaust system of the Solo 2625-01i, 2625-01i Neo, 2625-02i and 2625-02i Neo engines, which are installed in the Ventus-3 and the Arcus gliders.

It is the Solo spare part 25 00 850.

This toothed belt is 2400 mm and is adapted for the Ventus-2cM pylon with a Solo 2625-01 engine.

This water pompe is used for all the SOLO engines 2625.

This throttle valve sensor mounted (Solo part number 23 00 910) is used in the Solo 2625 01i, Solo 2625 01i Neo and 2625 02i.

 

This 2520 Poly Chain GT2 toothed belt is designed for the pylon of the Nimbus-4M and Nimbus-4DM equipped with a Solo engine 2625.

Solo part: 23 00 781 02

Starter from Denso for Solo engine 2625.

This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.

 

This kit contains all the fuel hoses that need to be replaced during the 5 years inspection on the Arcus M.

This RPM sensor with cables and pins is used for the Solo 2625-02i.

This item is 1 set of 5 pieces.

SOLO spare-part n° 00 57 225

 

This item is 1 set of 5 pieces.

SOLO spare-part n° 00 57 224

 

This hoses are assembled with a filter and the connections to refuel your glider.

This hose set is designed for use with the Solo 2625 02 and 02i engines in the Arcus M and Arcus M edition 2020 gliders.

Optional Spindle Drive Modification for Maintenance & Production according to TN A532-12

Our spindle drive system, responsible for extending and retracting the power plant, is designed with rubber-mounted suspension for optimal vibration isolation. This optional modification increases reliability.

Within the scope of maintenance and manufacture, it is also permissible to replace only the front, fuselage-side suspension (Action 1) or only the rubber mount of the rear, propeller arm-side suspension (Action 2).

• Kit 1: Front Suspension: Integrated within the fuselage
• Kit 2: Rear Suspension: Mounted on the propeller arm

This part is used for the Discus bM, the Ventus-2cM, the Ventus-3M, the Nimbus-4DM and the Arcus M.

This proximity switch (ref  IX02 0815) is used for the automatic propeller brake in the Arcus M. 

It is not addapted to the Arcus M edition 2020.

This position sensor is sold as a unit (you might need two of them) and the FUT plug is included.

 

This fuel tube is use for the Nimbus-4D T, the Duo Discus T, Duo Discus xL T and the Arcus T.

This sensor is used in the Solo 2625 01 and 2625 02 to measure the water temperature.

The sensor used on the Arcus M and Ventus-3M (Solo 2625 01i and 02i) is different. You can find it on the suggested products.

This air filter RC-1060 (Solo ref: 25 00 845) is used for the 2625-02i.

It used to be rectangular but the shape changed. You can use this model instead of the square ones.

This rubber element is use for the engine mount of the Arcus M, the Ventus-3M, Ventus-2cM, the Ventus-2cxM, the Nimbus-4M and the Nimbus-4DM.

Its old reference is VW 431407181D.

 

The kit contains the cable (diameter 3,2 mm), 2 nicopress-oval sleeves, 2 thimbles and some silicone tube. One side is already assembled.

It can be use for the Ventus-2cM, Ventus-3M, the Nimbus-4M and -4DM and the Arcus M.

Please refer to the maintenance manual for the installation.

These filters (reference 6064-0A / 0 450 905 401 and E230204) are used for the fuel system of the Ventus-3M.

This coupling is used for the fuel line going to the wing tank of the Ventus-3M and the Arcus M.

Please make sure you are entitled and have the skills to change that part. It should be secured with Loctite 577.

Please note: The coupling for the vent line is different. 

This sensor is used in the Solo 2625 01i and 2625 02i engines to measure water temperature.

Please note that the sensor used in the older Solo 2625 model is different. You can find it under the suggested products.

This ignition cable is 35 cm long and it is used for the Arcus M.

You will need 4 units. if you want to change all of them.

This air filter RU 2690 (Solo ref: 25 00 580) is used for the Solo 2625-01 and 2625-02.

This pneumatic spring is 820 mm long. It is used for the Duo Discus T, Duo Discus xT, Duo Discus xLT, the Arcus T and Arcus T edition 2020.

These filters (1 filter Pierburg 4.00030.80.0 and 1 filter KL14 Mahle) are used for the fuel system of the Arcus M.

This rubber element is part of the spindelsuspension of the Ventus-2cM, Ventus-3M, Nimbus-4M, -4DM and Arcus M.

It is 34 mm long.

Depending on the equipment available to you, it might be easier to buy the complete part (B40-13772). See suggested products.

This gas strut is 500N and it is used for the engine mount of the Ventus T, Discus T, Ventus cM, the Nimbus-3T and the Nimbus-4T.

More modern single seaters are using the reference L03-0122, that is 600N. You can find it on the suggested product.

This plate is used for the Duo Discus T, Duo Discus xT, Duo Discus xLT, the Arcus T and Arcus T edition 2020.

This lid is used for the cooler of all the Ventus-3M (Solo 2625-01i and 2625-01i neo) and all the Arcus M (Solo 2625-02i) after 2018 but not for the other version. 

Please note that if the radiator of your glider is not black, you might need a different lid. Please contact Spare Parts.

This gummi piece is used to connect the spark plug in the SOLO 2625 and 2350 engines.

SOLO spare part n° 23 00 701 V1

This part was originally black, then changed to red, and has now been superseded by this new reference.

This propeller brake pad is designed for the propellers of the almost all the Ventus-2cM, Ventus-3M, and all Arcus M models.

Some Nimbus-4M and Nimbus-4DM gliders may also be equipped with this system if Technical Note 868-19 has been applied.

This screw is M10 x 58.

It is used for the rear spindle suspension of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM

Gasket exhaust is used for the SOLO engines 2625.

It is 68,5 x 48 x 2 mm.

It is sold by the unit.

These three brass bushes are used for the propellor stopper of the Ventus-3M and the Arcus M edition 2020. The bush in the centre is 8 x 1 x 9.3 mm and the two on the side are 8 x 1 x 6.7 mm.

They can be damaged by the spring and this creates some play in the stopper.

 

This hose NW 4,8x1,6 mm is transparent and it is use for the Fuel sytem.

It is sold my the meter.

SOLO Silent block bush, spare part n° 00 94 240

It is 14 mm large and its diameter is 37 mm.

This spark plug is used for all SOLO engines.