Shop

This is used only in case of exchange, to ship the new part

Nicopress-oval sleeve 1,5-2 mm, ref : NT281C-A or N° 28-1-C.

It is 10 x 6 x 4 mm.

Nicopress-oval sleeve 1,5-2 mm, ref : NT281C-A or N° 28-1-C.

It is 10 x 6 x 4 mm.

This washer is used for the tail ballast dump valve of most of the Schempp-Hirth gliders.

Thimble  2,5 mm galvanized.

It is 27 x 15 x 5 mm.

This safety ring-spring steel, DIN471, size 12 is used to secure the tailwheel axle of, almost, all Schempp-Hirth gliders.

This oval countersunk head screw is used for the seat pan.

It is size M 5 x 16.

Safety nut, DIN 985 galvanized

Availabe in thread size M6 or M8.

Washer M06 galvanized, DIN 125 / ISO 7090 Form B

This washer is mainly used on the rear part of the horizontal tail fitting.

This copper seal ring is 10 x 14 x 1,5 , DIN 7603 Form A. 

It is used for the fuel line in the Arcus M and the Ventus-3M. 

It is also used for the brakes system Tost - Magura that you might have on the Discus-2b, -2c and Ventus-2c.

This washer is used for the tail ballast dump valve of most of the Schempp-Hirth gliders.

These cup washers are used for the bucket seat.

It is size M6 and its dimensions are 13 x 13 x 3 mm.

Tip: For a nicer finish, use these M6 washers with M5 screws (See suggested products).

These cup washers are used for the bucket seat.

It is size M6 and its dimensions are 13 x 13 x 3 mm.

Tip: For a nicer finish, use these M6 washers with M5 screws (See suggested products).

This 6k-Screw is used for the elevator drive U-bracket.

These roll pins are used to secure the aileron.

Dimension: 2 x 10 mm

DIN 1481 / ISO 8752

Roll pin DIN 1481 / ISO 8752 stainless.

They are (mainly) used to in trim of the Arcus, Duo Discus XL and Nimbus-4DL.

There is two models : On gliders produced after April 2015, you will probably need the 2 x 16 mm model. For the older glider you will need to use the 2x14 mm roll pins. Please have a look in your glider to confirm which models you need.

 

This washer is used with the DZUS-quick fastener pin. It is size 6, its diameter is 12 mm and it is made of plastic.

Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).

It is 5 x 5 x 5 mm.

Safety washers Form S available in M6 and M8.

These washers are used, among other things, to secure the rear part of the horizontal tail fitting and the elevator drive U-bracket.

This handle is made of plastic. It is 75 mm long and its diameter is 25 mm.

It is used for the airbrake handle of almost all Schempp-Hirth gliders.

This handle is made of plastic. It is 75 mm long and its diameter is 25 mm.

It is used for the airbrake handle of almost all Schempp-Hirth gliders.

This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.

This O-ring  Ø32 x Ø3 is used for the water dump valve of several gliders:

• the Duo Discus x and xL,
• all the Arcus,
• some Discus-2c (the system has been upgraded in 2005),
• the Ventus-2cx and the Ventus-2cxa for the inner wing dump system not the outer wing.

Nicopress-Stop sleeve 2,5 mm, NTG282G-100.

It is 10 x 9 x 6 mm.

Nicopress-Stop sleeve 2,5 mm, NTG282G-100.

It is 10 x 9 x 6 mm.

This rubber washer ensures the sealing of the tail ballast of most of the Schempp-Hirth gliders.
It is advisable to replace it every 4-6 years to avoid water leaks.

This bold is 6h11x28 mm, DIN 1434 / ISO 22341 and galvanized.

It is at the level of the pilot stick both front and back in the Duo Discus and the Nimbus-4D. With time, it can get rusty. 

It is sold here with its splint: 1,6 x 16, DIN 94 / ISO 1234 galvanized.

This washer is used for some Schempp-Hirth tailwheel axle with the original 200x50 with or without led.

It is Ø12,1XØ17X1,5.

 

Thimble  3,5 mm galvanized.

It is 32 x 17 x 6 mm.

This handle is used for the landing gear grip of all moderne single seaters (except Ventus-3). It is also the flap grip for the first Arcus and for the Ventus b and c. For those two latest,  it must be adapted, by cutting a few centimeters of it.

It is 99 mm long and 24 mm at the largest.

This elastic maintains the landing gear doors of the double seater. Its diameter is 5 mm.

You can order it by the meter.

Nicopress-Stop sleeve 3,0-3,5 mm, NT283M / n° 28-3-M.

It is 14 x 12 x 8 mm.

This safety pin (or Fokker pin) is 1,5 mm and it is used to secure the cockpit weight in Schempp-Hirth gliders.

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This 6k-screw is used for the elevator drive U-bracket.
 

This 6k-screw is used for the elevator drive U-bracket.
 

These hinges are used to fix the landing gear door of almost all single seater.

Their dimensions are: 30 x 30 x 0,8 mm

The countersunk screws (fuselage side) and countersunk-head rivet with their washers (door side) can be ordered as an option.

The tension spring Z-109AI is used for the single seater landing gear doors.

Its dimensions are 77 x 11 x 11 mm

This splint is used for the main landing gear of almost all Discus, Discus-2, Ventus-2 as well as the Ventus-3.

It is 3,2 x 40 ISO 1234.

 

This PVC adhesive tape extra fin (known as Tesa 4104) is used to fixe the profiband and to obtain a clean finish on the control sealing.

This tape is 67 µm thick and it is available in 3 different widths. Please refer to the sealing instruction of your glider to order the requiered sealing.

Each roll contains 66 meters of tape.

This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

This gummi ring is Ø60 x Ø10 and  is the tire of the wing wheel Lindner of the Duo Discus, Discus and the Ventus.

It is sold by the unit.

 

This screw is mainly used to secure the rear part of the horizontal tail fitting.

This turbulator band (or Noppenband) is 10 mm large. The dimples are 0,85 mm high and they are distanced by 16 mm.

This model is mainly used for the Arcus and the Ventus-3. Look at your sealing instructions for more information.

A roll is 10 meters.