The tension spring Z-109AI is used for the single seater landing gear doors.

Its dimensions are 77 x 11 x 11 mm

These hinges are used to fix the landing gear door of almost all single seater.

Their dimensions are: 30 x 30 x 0,8 mm

The countersunk screws (fuselage side) and countersunk-head rivet with their washers (door side) can be ordered as an option.

The clamp is suitable for hoses with diameters ranging from 6 mm to 7 mm and is used on some gliders for the rudder pedal cable.

The clamp is suitable for hoses with diameters ranging from 12 mm to 20 mm. It is specifically used in the fuel system of the Arcus M and Arcus T.

This pin is 84 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and has an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.

This 6k-screw is used for the elevator drive U-bracket.
 

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This screw is used for the Ventus-2c with a 5" Classic wheels from TOST and a Magura cylinder brake.

It is 25 mm long and the head size is 14 mm.

This pin is 40 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and does not have an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, all Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.

This is a galvanized, spring-loaded, self-locking hex nut in M10 size, manufactured to the SSB 003 specification with an FK4 flat design and a 17 mm wrench size.

It is used on the landing gear of nearly all Schempp-Hirth gliders, for the shock absorber and/or the drag strut.

Nicopress-Stop sleeve 3,0-3,5 mm, NT283M / n° 28-3-M.

It is 14 x 12 x 8 mm.

Thimble  3,5 mm galvanized.

It is 32 x 17 x 6 mm.

This rubber washer ensures the sealing of the tail ballast of most of the Schempp-Hirth gliders.
It is advisable to replace it every 4-6 years to avoid water leaks.

Nicopress-Stop sleeve 2,5 mm, NTG282G-100.

It is 10 x 9 x 6 mm.

Ring tongue terminal with closed barrel

• Stud size: M6 (≈ 6.73 mm)
• Wire range: 14 AWG (≈ 2 mm²)
• Insulation: Blue, partially insulated sleeve

Applications:

• Electrical power systems
• Ground connection on the wing fuel tank
• Ground connection on the nose

This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.

This washer is used with the DZUS-quick fastener pin. It is size 6, its diameter is 12 mm and it is made of plastic.

Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).

It is 5 x 5 x 5 mm.

Safety washers Form S available in M6 and M8.

These washers are used, among other things, to secure the rear part of the horizontal tail fitting and the elevator drive U-bracket.

This 6k-Screw is used for the elevator drive U-bracket.