This pushrod guide ball cage measures 29 × 3 × 20 mm.

Please note that another model exists with dimensions 25 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This piece is used to protect the spark plug from the rain in the SOLO 2350 engine.

SOLO spare part n° 00 84 203

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This fuel filter Karcoma 99.106/8-100 is used for the refuelling and fuel hoses.

It is 80 mm long and its diameter is 30 mm.

Two models exist, with or without a base, please choose the model who is already on your glider.

They are 10 mm high.

They are sold individually but you will need 5 of them for your glider.

This perspex disc is made for Arcus, all Duo Discus, Ventus-3, Discus-2b, -2c, Discus b and cs.

However, some gliders have more than one perspex disc and they can be different. Please look at the diameter and model you need.

Its diameter is 78,3 mm and the central hole is 5 mm.

This screw is mainly used to secure the rear part of the horizontal tail fitting.

This pushrod guide ball cage measures 25 × 3 × 20 mm.

Please note that another model exists with dimensions 29 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This high-quality, flexible shrink tubing is used for insulation and protection of cables and connections – including many fuel lines and some electronic components.

Minimum diameter before shrinking: 12.7 mm

Diameter after shrinking: 6.4 mm

It is sold by the meter.

This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

The tension spring Z-109AI is used for the single seater landing gear doors.

Its dimensions are 77 x 11 x 11 mm

Tension Spring for the Discus-2 Trim System, Part No.: RZ-123 I

Tension spring for the trim system of the Discus-2 series. 3 springs are required per aircraft.

It is  Ø 1,6 x 14,1 x 59 mm

 

This tension spring (ref RZ-124) is used in the rudder pedal of the Arcus, Duo Discus, and Nimbus-4D gliders, in the rear position, with two springs installed per glider. It is also used for the doors of the engine box in single seater.

These hinges are used to fix the landing gear door of almost all single seater.

Their dimensions are: 30 x 30 x 0,8 mm

The countersunk screws (fuselage side) and countersunk-head rivet with their washers (door side) can be ordered as an option.

The clamp is suitable for hoses with diameters ranging from 6 mm to 7 mm and is used on some gliders for the rudder pedal cable.

The clamp is suitable for hoses with diameters ranging from 12 mm to 20 mm. It is specifically used in the fuel system of the Arcus M and Arcus T.

This butterfly nut is M10 (DIN 315) and it is used to secure the cockpit weights in all Schempp-Hirth single seaters (except the Ventus-3), the Nimbus, the Janus and some of the first Duo Discus.

This pin is 84 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and has an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.