This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.

This O-ring  Ø32 x Ø3 is used for the water dump valve of several gliders:

• the Duo Discus x and xL,
• all the Arcus,
• some Discus-2c (the system has been upgraded in 2005),
• the Ventus-2cx and the Ventus-2cxa for the inner wing dump system not the outer wing.

Nicopress-Stop sleeve 2,5 mm, NTG282G-100.

It is 10 x 9 x 6 mm.

This spring is designed for the airbrakes of all Schempp-Hirth gliders ecxcept the Ventus-3.

The spring is 1 x 10 x 30 mm.

Depending on your glider model, each airbrake may require 2 of these springs.

Important Note: This spring is used on the outside of the airbrakes. The other spring are straight (ref L03-0033). You can find them among our suggested products.

This rubber washer ensures the sealing of the tail ballast of most of the Schempp-Hirth gliders.
It is advisable to replace it every 4-6 years to avoid water leaks.

This bold is 6h11x28 mm, DIN 1434 / ISO 22341 and galvanized.

It is at the level of the pilot stick both front and back in the Duo Discus and the Nimbus-4D. With time, it can get rusty. 

It is sold here with its splint: 1,6 x 16, DIN 94 / ISO 1234 galvanized.

Thimble  3,5 mm galvanized.

It is 32 x 17 x 6 mm.

This washer is used for some Schempp-Hirth tailwheel axle with the original 200x50 with or without led.

It is Ø12,1XØ17X1,5.

 

This handle is used for the landing gear grip of all moderne single seaters (except Ventus-3). It is also the flap grip for the first Arcus and for the Ventus b and c. For those two latest,  it must be adapted, by cutting a few centimeters of it.

It is 99 mm long and 24 mm at the largest.

This elastic maintains the landing gear doors of the double seater. Its diameter is 5 mm.

You can order it by the meter.

Nicopress-Stop sleeve 3,0-3,5 mm, NT283M / n° 28-3-M.

It is 14 x 12 x 8 mm.

This safety pin (or Fokker pin) is 1,5 mm and it is used to secure the cockpit weight in Schempp-Hirth gliders.

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This 6k-screw is used for the elevator drive U-bracket.
 

These hinges are used to fix the landing gear door of almost all single seater.

Their dimensions are: 30 x 30 x 0,8 mm

The countersunk screws (fuselage side) and countersunk-head rivet with their washers (door side) can be ordered as an option.

The tension spring Z-109AI is used for the single seater landing gear doors.

Its dimensions are 77 x 11 x 11 mm

This splint is used for the main landing gear of almost all Discus, Discus-2, Ventus-2 as well as the Ventus-3.

It is 3,2 x 40 ISO 1234.

 

This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

This gummi ring is Ø60 x Ø10 and  is the tire of the wing wheel Lindner of the Duo Discus, Discus and the Ventus.

It is sold by the unit.