This plexi cover is made for the Janus, the Ventus b and some Ventus-2. It is used in the TN 349-42 / 825-57.

Its diameter is 53,5 mm and the central hole is 5 mm. The locking device is 100mm long.

 

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This gas strut is 500N and it is used for the engine mount of the Ventus T, Discus T, Ventus cM, the Nimbus-3T and the Nimbus-4T.

More modern single seaters are using the reference L03-0122, that is 600N. You can find it on the suggested product.

This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

This rubber element is part of the spindelsuspension of the Ventus-2cM, Ventus-3M, Nimbus-4M, -4DM and Arcus M.

It is 34 mm long.

Depending on the equipment available to you, it might be easier to buy the complete part (B40-13772). See suggested products.

This ignition cable is 35 cm long and it is used for the Arcus M.

You will need 4 units. if you want to change all of them.

This sealing lid is for the Arcus edition 2020.

It is equipped of a non-return valve.

This sealing is made for the Ventus-3 sealing caps.

Its diameter is 26 mm and the sealing is 4,0mm thick.

This sealing cap is made for the Ventus-3 outer wing.

The plug used for the inner wing is different. You can find it below in the suggested items.

Please note that the first seven Ventus-3 are equipped with a different system.

This sealing cap is made for the Ventus-3 inner wing.

The plug used for the outer wing is different. You can find it below in the suggested items.

Please note that the first seven Ventus-3 are equipped with a different system.

This skid is 194 x 47 x 37 mm and is used for all Duo Discus.

Double face tape is already fixed on the skid to make it easy to instal.

This skid is 164 x 48 x 36 mm is used for the Discus-2a, -2b and 2-c.

Double face tape is already fixed on the skid to instal it easily.

This skid is 121 x 35 x 28,5 mm and is used for Discus a, Discus b, Ventus b, Ventus c and all the Ventus-2.

Double face tape is already fixed on the skid to instal it easily.

This wingtip wheel is designed for the Arcus. It is aerodynamic but high enough and resistant to drive on the ground.

The item is 236 x 116 x 69 mm and the screws are 165 mm apart.

It sold by the unit and the screws are provided.

 

 

The Lindner system offers a great compromise between aerodynamic and ease of handling on the ground.

This wingtip wheel is designed for the Duo Discus and the Discus-2c. To install these wheels, your glider need to have the adapted fixation system.

The support, with the wheel, is 211 X 60 x 100 mm and has two holes for screws, that are 165 mm apart.

It is sold by the unit and the screws are included.

 

This wingtip wheel is made for the Ventus-2c.

This system is aerodynamic and compact (212 x 95 x 59 mm). In addition it is weighting only 200 g.

It is sold by the unit.

You can to fix it with screws that are included. Look at look wing tip, the holes are 165 mm apart.

This rubber ring is Ø80 x Ø10 and it is the tire of the wing wheel Lindner of the Arcus.

This wingtip wheel is 84 x 84 x 11 mm rim with a 60 x 10 O-Ring NBR70 tyre. It made for the Lindner system wingtip wheels of the Duo Discus, Discus-2c and the Ventus.

It is sold by the unit.