The deflection pulley is used to eliminate friction from the Bowden cables (in mosquito cleaner systems) in the event of major directional changes of the cable to enable lower manual force/power consumption and faster cleaning.

The visible part of the peg is 70,5 mm long with a 14 mm diameter. The internal part is 35 mm long, with a 40 mm diameter.

It is used on the back part of the Discus-2c and Ventus-2c wing roots.

This item is part of the horizontal tailplane fixation back system of all the modern Schempp-Hirth gliders. The kit provides all the necessary parts to change 1 pin.

Kit to secure l'hotellier connector for gliders with manual control hookups.

It cannot be used for the wing extension.

It is sold by the unit and the EASA Form 1 is included. 

These brake linings (Tost P/N 080949) are designed for the BZT2 brake assembly installed after 2017 with a thread M10x1. It is not compatible with the model with a thread NPT See drawing.

The BZT2 system is compatible with 5″ and 6″ disc brake wheels from the Penta and Classic series. It is commonly installed on the Ventus-3 and Arcus edition 2020 models.

Please note that different braking systems have been used over time, and several Technical Notices (TN) have been approved. Carefully inspect your brakes before ordering to ensure you select the correct brake pad.

This part is used for the notching of the flaps of the Ventus c.

It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.

This part can be adapted to fit the Discus-2a, Discus-2b, Discus-2c, Ventus-2ax, Ventus-2bx, the ventus-2c, the ventus-2cx and the Ventus-3.

It measures 148 mm in width. 

Please note that you will need to cut the part to ensure it fits your glider, as it is sold in an untrimmed form.

This sealing lid is for the Arcus edition 2020.

It is equipped of a non-return valve.

This comprehensive kit ensures compatibility with all Duo Discus equipped with a master cylinder model 7 / brakes 30-9. It provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 4000 mm of 1,8 mm cable
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

This plexi cover is made for the Janus, the Ventus b and some Ventus-2. It is used in the TN 349-42 / 825-57.

Its diameter is 53,5 mm and the central hole is 5 mm. The locking device is 100mm long.

 

These filters (reference 6064-0A / 0 450 905 401 and E230204) are used for the fuel system of the Ventus-3M.

This kit includes a wide selection of spacer washers for tail wheel axle, measuring 16 x 2 mm with widths ranging from 1.5 to 6 mm. It is particularly useful if you plan to switch from a classic tailwheel to a mini version. Compatible with most gliders, except for the Arcus M, Ventus-3M, and Cirrus.

This proximity switch (ref  IX02 0815) is used for the automatic propeller brake in the Arcus M. 

It is not addapted to the Arcus M edition 2020.

This position sensor is sold as a unit (you might need two of them) and the FUT plug is included.

 

This air filter RC-1060 (Solo ref: 25 00 845) is used for the 2625-02i.

It used to be rectangular but the shape changed. You can use this model instead of the square ones.

This sensor is used in the Solo 2625 01 and 2625 02 to measure the water temperature.

The sensor used on the Arcus M and Ventus-3M (Solo 2625 01i and 02i) is different. You can find it on the suggested products.

Thees oxygen bottle holders are suitable for a majority of pure Schempp-Hirth gliders.

Please choose which holder you need according to the diameter of your Oxygen-bottle.  It is possible to adjust the holder at +/- 2mm.

In single-seaters, one of the screws of the holder is often above the spar bridge, where the wall is relatively thin. It is therefore often necessary to add the washer B40-2218 (see suggested products).

This microphone is adapted for radio with dynamic input.

It is delivered with the nut and the safety lock.

You can add the Schempp-Hirth microphone mounting as an option.

This 200N gas strut is in the airbrake box. It connects the airbrake rod to the actuating lever of the trailing edge flap for the Duo Discus X and xL as well as the Nimbus-3D, -4 and -4D.

An older version used a gas spring from the company Hahn, you can use this one instead.

This part can be adapted to fit the Duo Discus, Duo Discus X, Duo Discus XL, as well as the Arcus, Arcus Edition 2020, and Nimbus-4D.

It measures approximately 147 mm in width and 157 mm in length.

Please note that the part is sold in an untrimmed form, so you will need to cut it to ensure a proper fit for your glider.

This part is used for the Discus bM, the Ventus-2cM, the Ventus-3M, the Nimbus-4DM and the Arcus M.

This 150N gas strut is used for the Mini-Nimbus airbreaks.

 

This gaz strut is 210N and it is used for the landing gear on the Arcus and Duo Discus XL. 

Important: It is not adapted for Beringer wheels.

Two models exist. The pivot ball was first associated with a M5 screw, before beeing replace by a M6 screw in 2015. Please measure the diameter of the screw on the part that you are currently using, and order the same.

An assembly jig for the tension pneumatic spring can be added as an option. If you don't have one, we advise you to buy it.

This hose set is designed for use with the Solo 2625 02 and 02i engines in the Arcus M and Arcus M edition 2020 gliders.

This hoses are assembled with a filter and the connections to refuel your glider.

This item is part of the stabilizer fixation of all the modern Schempp-Hirth gliders.

It is possible to replace or change it for a bigger pin diameter to compensate the ageing of the parts on the stabilizer.

This item is delivered with 4 allen screw M06x30 - 8.8, DIN 912 / ISO 4762 galvanized (L01-0119) and 4 Schnorr-safety washer M6 (L01-0378).

This oxygen bottle holder is suitable for a majority of gliders equiped with a turbo or a motor.

Please choose which holder you need according to your Oxygen-bottle diameter.  It is possible to adjust the holder at +/- 2 mm.

In single-seaters, one of the screws of the support is often above the spar bridge, where the wall is relatively thin. It is therefore often necessary to add the washer B40-2218 (see suggested products).

This microphone is adapted to radio with electret input.

Mounting kit is included in the price.

This rubber skid is 330 x 70mm and it is adapted to all Schempp-Hirth gliders including Cirrus and Nimbus.

 

This 2.80/2.50-4 tire is used for the front wheel of the Janus, Duo Discus, and Arcus.

Previously, a 3" tire (D 3.00-4 IND IC35 4PR) was used, but that model has been discontinued. This tire serves as a suitable replacement.

This drive funnel is used on almost all Schempp-Hirth gliders except the Nimbus-4 and the Ventus-3.

Two lock nuts M 6-8, DIN 985 and a lock nut M6 TRELOC, DIN 439 are included. However, your glider has a specific set of distance washer that are not provided. Please before disassemble the funnel make sure you know which washer go where.

On the Ventus-2 and Discus-2c, you may also need a set of screws that can be baught as an option.

This item is 1 set of 5 pieces.

SOLO spare-part n° 00 57 224

 

This wheel is made by Tost for the tail of the Arcus M, Ventus-3M and the Quintus M.

It is made in two parts, and it is adapted for a 12 mm axle and 200 x 50 tyres and tubes. In aluminium, silver anodized, it weights less than a kilo.

This RPM sensor with cables and pins is used for the Solo 2625-02i.

This tire (Tost p/n 065221 ) is a special 5" made by TOST AERO for the Discus-2b, -2c, the Ventus-2c and the Ventus-3 . It is a bit smaller than a classic 5" so the tyre is not touching the landing gear box.