This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

This 300 N gas strut is 313 mm long.

It is used for the foldable instr. panel of the Discus-2c FES, Discus b, Ventus c and Ventus-2b.

This 350 N gas strut is 293 mm long.

It is used for the foldable instrument panel of the Ventus-2c, Ventus-2bx, Discus-2a, Discus-2b and Discus-2c. 

This gas strut is 450 N and 178 mm long.

It is used for the foldable instrument panel of Arcus and Duo Discus XL.

This 6k-screw is used for the elevator drive U-bracket.
 

This 6k-Screw is used for the elevator drive U-bracket.

This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.

Safety nut, DIN 985 galvanized

Availabe in thread size M6 or M8.

This gas strut is 500N and it is used for the engine mount of the Ventus T, Discus T, Ventus cM, the Nimbus-3T and the Nimbus-4T.

More modern single seaters are using the reference L03-0122, that is 600N. You can find it on the suggested product.

These roll pins are used to secure the aileron.

Dimension: 2 x 10 mm

DIN 1481 / ISO 8752

This part is used for the notching of the flaps of the Ventus c.

It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.

Washer M06 galvanized, DIN 125 / ISO 7090 Form B

This rubber element is part of the spindelsuspension of the Ventus-2cM, Ventus-3M, Nimbus-4M, -4DM and Arcus M.

It is 34 mm long.

Depending on the equipment available to you, it might be easier to buy the complete part (B40-13772). See suggested products.

This perspex disc is made for the Ventus-2a.

Its diameter is 53,5 mm and the central hole is 5 mm.

This ignition cable is 35 cm long and it is used for the Arcus M.

You will need 4 units. if you want to change all of them.

This gasket is used for the canopy of the Duo Discus and the Arcus.

It is sold by the meter.

This is the handle for the trim of the Arcus, Duo Discus XL and Nimbus-4DL.

The roll pins are included. 

Please note the pin roll can be bought separatly (see suggested product). If your glider is older than April 2015, you need to use the 2x14 mm roll pins instead of 2x16 mm.

 

This spring is used for the trim of the Arcus, Duo Discus XL, Nimbus-4DL and all the Discus from the Discus a to the Discus-2c.

It is 25mm lage and the legs are 40mm long. The central part is 12,5mm.

Some glider need roll pins. They are not included but they can be baught individaly (see the suggested products). 

Roll pin DIN 1481 / ISO 8752 stainless.

They are (mainly) used to in trim of the Arcus, Duo Discus XL and Nimbus-4DL.

There is two models : On gliders produced after April 2015, you will probably need the 2 x 16 mm model. For the older glider you will need to use the 2x14 mm roll pins. Please have a look in your glider to confirm which models you need.

 

Rod end bearing with a 14c6 head and M8 x 58 length body.

Other rod end bearings are used in our gliders. If you are not sure which one you need. Please contact the Spare Part team.

SOLO Silent block bush, spare part n° 20 61 395

 

This piece is used to protect the spark plug from the rain in the SOLO 2350 engine.

SOLO spare part n° 00 84 203

Safety washers Form S available in M6 and M8.

These washers are used, among other things, to secure the rear part of the horizontal tail fitting and the elevator drive U-bracket.

This screw is mainly used to secure the rear part of the horizontal tail fitting.

This washer is mainly used on the rear part of the horizontal tail fitting.

This 6k-Screw is mainly used at the rear part of the horizontal tail fitting.
 

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2c and Discus-2c.

This kit contains all the fuel hoses that need to be replaced during the 5 years inspection on the Arcus M.

These fuses are used for instruments.

They are available in 2, 4 and 6,3 A.

This sensor is used in the Solo 2625 01 and 2625 02 to measure the water temperature.

The sensor used on the Arcus M and Ventus-3M (Solo 2625 01i and 02i) is different. You can find it on the suggested products.

This sensor is used in the Solo 2625 01i and 2625 02i engines to measure water temperature.

Please note that the sensor used in the older Solo 2625 model is different. You can find it under the suggested products.

This hoses are assembled with a filter and the connections to refuel your glider.

This RPM sensor with cables and pins is used for the Solo 2625-02i.

This M8 screw is design for the steering tail wheel axle of the Arcus-M and the Ventus-3M.

 

This axle is design for the steering tail wheel of the Arcus-M and the Ventus-3M.

 

This air filter RU 2690 (Solo ref: 25 00 580) is used for the Solo 2625-01 and 2625-02.

This tension spring is 1,02 x 11 x 72 mm.

It is used for the arresting cables of the Ventus-2cT, -2cxT and Discus-2cT with engine Solo 2350.

 

This washer is  16 x 2 x 4,5 mm and it is used for the tail wheel 

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This plexi cover is made for the Janus, the Ventus b and some Ventus-2. It is used in the TN 349-42 / 825-57.

Its diameter is 53,5 mm and the central hole is 5 mm. The locking device is 100mm long.

 

This item is 1 set of 5 pieces.

SOLO spare-part n° 00 57 225