This safety pin (or Fokker pin) is 1,5 mm and it is used to secure the cockpit weight in Schempp-Hirth gliders.

This screw is used for the Ventus-2c with a 5" Classic wheels from TOST and a Magura cylinder brake.

It is 25 mm long and the head size is 14 mm.

This foil sealing ring has a diameter of 95 mm and is used to cover the handhole cap of the Duo Discus, Arcus, Discus-2b, Discus-2c, Discus b, Discus cs und Ventus-3 and Ventus-3.

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This Elesa knurled head screw (M6x16) is used for various functions, including the adjustment mechanism of the headset position.

This 6k-screw is used for the elevator drive U-bracket.
 

This pin is 84 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and has an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.

The clamp is suitable for hoses with diameters ranging from 12 mm to 20 mm. It is specifically used in the fuel system of the Arcus M and Arcus T.

The clamp is suitable for hoses with diameters ranging from 6 mm to 7 mm and is used on some gliders for the rudder pedal cable.

These hinges are used to fix the landing gear door of almost all single seater.

Their dimensions are: 30 x 30 x 0,8 mm

The countersunk screws (fuselage side) and countersunk-head rivet with their washers (door side) can be ordered as an option.

This washer is used to adjust the distance between the wing and the fuselage. It is 0.3 mm thick.

They fit an 18 mm wing bolt, including both the front and rear bolts at the wing root of two-seater aircraft.

The washers have an internal diameter of 17.8 mm. They are slightly smaller than the bolt to ensure they stay in place when installed.

A kit containing eight washers with a thickness of 0.5 mm and four washers with a thickness of 0.8 mm is also available.

The tension spring Z-109AI is used for the single seater landing gear doors.

Its dimensions are 77 x 11 x 11 mm

This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

This high-quality, flexible shrink tubing is used for insulation and protection of cables and connections – including many fuel lines and some electronic components.

Minimum diameter before shrinking: 12.7 mm

Diameter after shrinking: 6.4 mm

It is sold by the meter.

This pushrod guide ball cage measures 25 × 3 × 20 mm.

Please note that another model exists with dimensions 29 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This screw is mainly used to secure the rear part of the horizontal tail fitting.

This perspex disc is made for Arcus, all Duo Discus, Ventus-3, Discus-2b, -2c, Discus b and cs.

However, some gliders have more than one perspex disc and they can be different. Please look at the diameter and model you need.

Its diameter is 78,3 mm and the central hole is 5 mm.

Two models exist, with or without a base, please choose the model who is already on your glider.

They are 10 mm high.

They are sold individually but you will need 5 of them for your glider.

This fuel filter Karcoma 99.106/8-100 is used for the refuelling and fuel hoses.

It is 80 mm long and its diameter is 30 mm.