Tail
-
Brass bushing for lower rudder framework fin of the Discus-2, Ventus-2, Ventus-3 Sport, Duo Discus and some Arcus
This brass bushing is part of the lower framework of the rudder fin on Ventus-2, Discus-2, Ventus-3 sport, all Duo Discus and Arcus (except Arcus M).
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On older gliders the diameter of the head is 14mm instead of 16mm. See bellow the suggested products.
from 1 € 7.26 incl. 19% VAT
€ 6.10 -
Allen screw M06x21 - 8.8, DIN 912 galvanized
This screw is mainly used to secure the rear part of the horizontal tail fitting.from 1 € 3.20 incl. 19% VAT
€ 2.69 -
Hexagon Screw 06036, LN 9037
This 6k-screw is used for the elevator drive U-bracket.
from 1 € 1.71 incl. 19% VAT
€ 1.44 -
Washer Ø12,1XØ17X1,5 for the tailwheel axle
This washer is used for some Schempp-Hirth tailwheel axle with the original 200x50 with or without led.
It is Ø12,1XØ17X1,5.
from 1 € 0.94 incl. 19% VAT
€ 0.79 -
ball bearing 6804-2RS
This deep groove ball bearing (6804-2RS, 20E1, DIN 625) is 20 mm inner diameter, 32 mm outer dimeter, 7 mm width, with seals on both sides.
It is used for the rear part of the horizontal tailplane fitting (item B40-0824), serving as a bearing support for the airbrake drive shaft.
from 1 € 0.93 incl. 19% VAT
€ 0.78 -
Rubber washer 19x3 mm for the fin tank dump valve
This rubber washer ensures the sealing of the tail ballast of most of the Schempp-Hirth gliders.
It is advisable to replace it every 4-6 years to avoid water leaks.from 1 € 0.82 incl. 19% VAT
€ 0.69 -
Schnorr-safety washer
Safety washers Form S available in M6 and M8.
These washers are used, among other things, to secure the rear part of the horizontal tail fitting and the elevator drive U-bracket.
from 1 € 0.48 incl. 19% VAT
€ 0.40 -
Hexagon Screw M06x18 - 8.8, DIN 933 / ISO 4017
This 6k-Screw is used for the elevator drive U-bracket.from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Washer Ø4,3xØ20x1,25 DIN 522 for the fin tank dump valve
This washer is used for the tail ballast dump valve of most of the Schempp-Hirth gliders.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
washer 6,4, DIN 9021 / ISO 7093-1 galvanized
This washer is mainly used on the rear part of the horizontal tail fitting.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Self-locking hexagonal-head nut, M8, DIN 14441
This slotted hexagonal-head nut, M8, DIN 14441 is copper plated and is commonly used for rudder fixation.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Safety ring-spring steel, DIN471, size 12
This safety ring-spring steel, DIN471, size 12 is used to secure the tailwheel axle of, almost, all Schempp-Hirth gliders.from 1 € 0.24 incl. 19% VAT
€ 0.20
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.