Cockpit
-
Landing gear guide plate
This plate in grey PVC is used as a guide for all single-seater landing gear (except for the Ventus-3).
Its length is 220 x 24 mm and there is no hole. Adjust it to your glider.
from 1 € 6.47 incl. 19% VAT
€ 5.44 -
Gasket for the canopy of single-seaters
Gasket for the canopy frame of single-seat gliders, sold by the metre.
Please note: some gliders have this gasket on one side only, with a different seal on the other side (the one used for the two-seaters, see recommanded product). Please check your glider carefully before ordering.
from 1 € 6.49 incl. 19% VAT
€ 5.45 -
Spring-loaded pull button
This indexing plunger without lock is used for the adjustment mechanism of the headset position in all Arcus M models, and for the oxygen bottle mount in the Arcus Edition 2020 and Ventus-3.from 1 € 6.71 incl. 19% VAT
€ 5.64 -
MPX-PIK cable, 30 cm
This MPX-PIK male cable (cross-section 2.5 mm², length 30 cm) connects the most of the modern glider’s electrical system to a battery equipped with an MPX female connector.from 1 € 7.52 incl. 19% VAT
€ 6.32 -
DZUS-quick fastener pin, Nextel painted
This quarter-turn lock is size 6, made in steel and with a left-hand thread.
This modell is Nextel painted, you can find the raw one bellow with the suggested products.
It is not adapted to all system. Please have a look and if your glider is equipped with the S-shaped system, order the reference L01-0045 via the spare part online form.
from 1 € 7.73 incl. 19% VAT
€ 6.50 -
Magnet for Ventus-2c, Discus-c and Double seater canopy closing mecanism
from 1 € 7.83 incl. 19% VAT
€ 6.58 -
Filter WK 21 for pitot
This WK 21 filter is used for the pitot tube in the glider’s nose.from 1 € 8.19 incl. 19% VAT
€ 6.88 -
Flap handle for some Ventus-2c and the Ventus-3
from 1 € 10.04 incl. 19% VAT
€ 8.44 -
Gasket for canopy frame of the Double Seaters
This gasket is used for the canopy of the Duo Discus and the Arcus.
It is sold by the meter.
from 1 € 10.60 incl. 19% VAT
€ 8.91 -
Eta fuse for instuments
These fuses are used for instruments.
They are available in 2, 4 and 6,3 A.
from 1 € 13.09 incl. 19% VAT
€ 11.00from 1 € 20.40 incl. 19% VAT
€ 17.14from 1 € 11.33 incl. 19% VAT
€ 9.52 -
Foam sealing
from 1 € 13.09 incl. 19% VAT
€ 11.00 -
Eyelet at landing gear doors for all models
These eyelet is used for the landing gear doors for all models.from 1 € 14.29 incl. 19% VAT
€ 12.01 -
Green ball knob for trim
This handle for the trim is a format 25 mm, M6. It is made in aluminium and green powdered.
from 1 € 18.34 incl. 19% VAT
€ 15.41 -
Flat spring for Janus, Nimbus-2, -3D, -4D flap drive
This tension spring is used to maintain the flap handle on the right position.
On the Janus B and Nimbus-2, it is located near the front seat handle.
Originally, the Janus C, the Nimbus-3D and the Nimbus-4D are using another spring that looks very different (ref B40-2417) and that is located on the back seat cockpit wall. However some gliders have been modified and they are now using this flat spring but near the spar bridge.
The other reference is available below under the suggested products.
from 1 € 18.64 incl. 19% VAT
€ 15.66 -
Cable roll with bearing 626 ZZ
This pulley with 626-ZZ bearing is used for the hook release mechanism and for some turbo actuation systems.from 1 € 19.23 incl. 19% VAT
€ 16.16 -
Flap position symbol for the Arcus
This label is made for the original Arcus.
from 1 € 20.93 incl. 19% VAT
€ 17.59 -
![20200506_143644[1].jpg](/uploads/tx_aimeos/preview/a/9/a904b500_preview_7_2_723d233329ac79fc23d6f2cfc6a05874_jpg.jpg?v=20211021145126)
Pneumatic tension spring 450 N for Ins. Panel for the Duo Discus xL and the Arcus
This gas strut is 450 N and 178 mm long.
It is used for the foldable instrument panel of Arcus and Duo Discus XL.
from 1 € 23.73 incl. 19% VAT
€ 19.94 -
Pneumatic tension spring 300 N for instr. panel of the Discus b, Discus-c, Ventus c, Ventus-2b
This 300 N gas strut is 313 mm long.
It is used for the foldable instr. panel of the Discus-2c FES, Discus b, Ventus c and Ventus-2b.
from 1 € 27.73 incl. 19% VAT
€ 23.30 -
Canopy hinge for Discus, Discus-2, Ventus, Ventus-2, Ventus-3 Sport, Duo Discus, Duo Discus X and Nimbus-4D
This hinge is in carbon fiber.
Note: The rear hinge can be different. To order it, please contact Schempp-Hirth spare part.
from 1 € 27.95 incl. 19% VAT
€ 23.49 -
Cockpit symbol for Ventus-3
This label is made for the Ventus-3.
from 1 € 28.24 incl. 19% VAT
€ 23.73 -
![20200506_142704[1].jpg](/uploads/tx_aimeos/preview/1/d/1d34449b_preview_0_b_0b8c0c31722775c34c5c39c2989c4c2c_jpg.jpg?v=20211021145114)
Pneumatic tension spring 350 N for Ins. Panel of the Discus-2b,-2c and Ventus-2c
This 350 N gas strut is 293 mm long.
It is used for the foldable instrument panel of the Ventus-2c, Ventus-2bx, Discus-2a, Discus-2b and Discus-2c.
from 1 € 28.63 incl. 19% VAT
€ 24.06
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.