This is a 3,2 washer DIN 9021 / ISO 7093-1 galvanized.

This washer is used to adjust the distance between the wing and the fuselage. It is 0.3 mm thick.

They fit an 18 mm wing bolt, including both the front and rear bolts at the wing root of two-seater aircraft.

The washers have an internal diameter of 17.8 mm. They are slightly smaller than the bolt to ensure they stay in place when installed.

A kit containing eight washers with a thickness of 0.5 mm and four washers with a thickness of 0.8 mm is also available.

This brass bushing (13x1.5x6.5 mm) is used on the front elevator mount of the Standard Cirrus.

 

This propeller brake pad is designed for the propellers of the almost all the Ventus-2cM, Ventus-3M, and all Arcus M models.

Some Nimbus-4M and Nimbus-4DM gliders may also be equipped with this system if Technical Note 868-19 has been applied.

This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.

 

This support is used for the lower rudder of the Arcus M.

The EASA Form one is included.

This high-quality, flexible shrink tubing is used for insulation and protection of cables and connections – including many fuel lines and some electronic components.

Minimum diameter before shrinking: 12.7 mm

Diameter after shrinking: 6.4 mm

It is sold by the meter.

This 2520 Poly Chain GT2 toothed belt is designed for the pylon of the Nimbus-4M and Nimbus-4DM equipped with a Solo engine 2625.

This hose set is designed for use with the Solo 2625 02 and 02i engines in the Arcus M and Arcus M edition 2020 gliders.

This throttle valve sensor mounted (Solo part number 23 00 910) is used in the Solo 2625 01i, Solo 2625 01i Neo and 2625 02i.

 

Thesef felt rings measure 20x10 mm and are 3 mm thick. They are designed for 14 C6 bearings.

Please note that a thinner model (L07-0594) is used for 10 C6 bearings.

These brake linings (Tost P/N 080949) are designed for the BZT2 brake assembly installed after 2017 with a thread M10x1. It is not compatible with the model with a thread NPT See drawing.

The BZT2 system is compatible with 5″ and 6″ disc brake wheels from the Penta and Classic series. It is commonly installed on the Ventus-3 and Arcus edition 2020 models.

Please note that different braking systems have been used over time, and several Technical Notices (TN) have been approved. Carefully inspect your brakes before ordering to ensure you select the correct brake pad.

This fiberglass bracket is designed for 7.5 Ah battery holders.

It has a width of 38 mm and fits a 97 mm battery. The shape is straight. 

A similar model (F60-0651) features a bend and is used in several gliders, including the Duo Discus XL and the Arcus. Please check the model installed in your glider carefully before purchasing.

This slotted hexagonal-head nut, M8, DIN 14441 is copper plated  and is commonly used for rudder fixation.

This spring is designed for the airbrakes of all Schempp-Hirth gliders ecxcept the Ventus-3.

The spring is 1 x 10 x 30 mm.

Depending on your glider model, each airbrake may require 2 of these springs.

Important Note: This spring is used on the outside of the airbrakes. The other spring are straight (ref L03-0033). You can find them among our suggested products.

This spring is designed for the airbrakes of all Schempp-Hirth gliders.

The spring is 0.8 mm x 7.8 mm x 30 mm.

Depending on your glider model, each airbrake may require between 9 and 11 of these springs.

Important Note: The exterior springs often differ from this ones. You can find the suitable exterior springs (ref L03-0032) among our suggested products.

 

This part can be adapted to fit the Duo Discus, Duo Discus X, Duo Discus XL, as well as the Arcus, Arcus Edition 2020, and Nimbus-4D.

It measures approximately 147 mm in width and 157 mm in length.

Please note that the part is sold in an untrimmed form, so you will need to cut it to ensure a proper fit for your glider.

This comprehensive kit ensures compatibility with all Duo Discus equipped with a master cylinder model 7 / brakes 30-9. It provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 4000 mm of 1,8 mm cable
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

This kit includes a wide selection of spacer washers for tail wheel axle, measuring 16 x 2 mm with widths ranging from 1.5 to 6 mm. It is particularly useful if you plan to switch from a classic tailwheel to a mini version. Compatible with most gliders, except for the Arcus M, Ventus-3M, and Cirrus.

This cover is designed to fit the TOST Mini 150 wheel.

If your glider is currently equipped with a classic Schempp-Hirth tailwheel, you can upgrade to the more compact TOST Mini 150. To make this conversion, you'll need this cover, a TOST Mini wheel, and a set of washers. All required components are listed below.