This is a galvanized, spring-loaded, self-locking hex nut in M10 size, manufactured to the SSB 003 specification with an FK4 flat design and a 17 mm wrench size.

It is used on the landing gear of nearly all Schempp-Hirth gliders, for the shock absorber and/or the drag strut.

This pin is 84 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and has an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.

This is a 3,2 washer DIN 9021 / ISO 7093-1 galvanized.

This brass bushing (13x1.5x6.5 mm) is used on the front elevator mount of the Standard Cirrus.

 

This propeller brake pad is designed for the propellers of the almost all the Ventus-2cM, Ventus-3M, and all Arcus M models.

Some Nimbus-4M and Nimbus-4DM gliders may also be equipped with this system if Technical Note 868-19 has been applied.

This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.

 

This support is used for the lower rudder of the Arcus M.

The EASA Form one is included.

This high-quality, flexible shrink tubing is used for insulation and protection of cables and connections – including many fuel lines and some electronic components.

Minimum diameter before shrinking: 12.7 mm

Diameter after shrinking: 6.4 mm

It is sold by the meter.

This 2520 Poly Chain GT2 toothed belt is designed for the pylon of the Nimbus-4M and Nimbus-4DM equipped with a Solo engine 2625.

This hose set is designed for use with the Solo 2625 02 and 02i engines in the Arcus M and Arcus M edition 2020 gliders.

This throttle valve sensor mounted (Solo part number 23 00 910) is used in the Solo 2625 01i, Solo 2625 01i Neo and 2625 02i.

 

Optional Spindle Drive Modification for Maintenance & Production according to TN A532-12

Our spindle drive system, responsible for extending and retracting the power plant, is designed with rubber-mounted suspension for optimal vibration isolation. This optional modification increases reliability.

Within the scope of maintenance and manufacture, it is also permissible to replace only the front, fuselage-side suspension (Action 1) or only the rubber mount of the rear, propeller arm-side suspension (Action 2).

• Kit 1: Front Suspension: Integrated within the fuselage
• Kit 2: Rear Suspension: Mounted on the propeller arm

Thesef felt rings measure 20x10 mm and are 3 mm thick. They are designed for 14 C6 bearings.

Please note that a thinner model (L07-0594) is used for 10 C6 bearings.

These brake linings (Tost P/N 080949) are designed for the BZT2 brake assembly installed after 2017 with a thread M10x1. It is not compatible with the model with a thread NPT See drawing.

The BZT2 system is compatible with 5″ and 6″ disc brake wheels from the Penta and Classic series. It is commonly installed on the Ventus-3 and Arcus edition 2020 models.

Please note that different braking systems have been used over time, and several Technical Notices (TN) have been approved. Carefully inspect your brakes before ordering to ensure you select the correct brake pad.

This fiberglass bracket is designed for 7.5 Ah battery holders.

It has a width of 38 mm and fits a 97 mm battery. The shape is straight. 

A similar model (F60-0651) features a bend and is used in several gliders, including the Duo Discus XL and the Arcus. Please check the model installed in your glider carefully before purchasing.

This slotted hexagonal-head nut, M8, DIN 14441 is copper plated  and is commonly used for rudder fixation.

This spring is designed for the airbrakes of all Schempp-Hirth gliders ecxcept the Ventus-3.

The spring is 1 x 10 x 30 mm.

Depending on your glider model, each airbrake may require 2 of these springs.

Important Note: This spring is used on the outside of the airbrakes. The other spring are straight (ref L03-0033). You can find them among our suggested products.

This spring is designed for the airbrakes of all Schempp-Hirth gliders.

The spring is 0.8 mm x 7.8 mm x 30 mm.

Depending on your glider model, each airbrake may require between 9 and 11 of these springs.

Important Note: The exterior springs often differ from this ones. You can find the suitable exterior springs (ref L03-0032) among our suggested products.

 

This part can be adapted to fit the Duo Discus, Duo Discus X, Duo Discus XL, as well as the Arcus, Arcus Edition 2020, and Nimbus-4D.

It measures approximately 147 mm in width and 157 mm in length.

Please note that the part is sold in an untrimmed form, so you will need to cut it to ensure a proper fit for your glider.

This comprehensive kit ensures compatibility with all Duo Discus equipped with a master cylinder model 7 / brakes 30-9. It provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 4000 mm of 1,8 mm cable
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

This kit includes a wide selection of spacer washers for tail wheel axle, measuring 16 x 2 mm with widths ranging from 1.5 to 6 mm. It is particularly useful if you plan to switch from a classic tailwheel to a mini version. Compatible with most gliders, except for the Arcus M, Ventus-3M, and Cirrus.

This cover is designed to fit the TOST Mini 150 wheel.

If your glider is currently equipped with a classic Schempp-Hirth tailwheel, you can upgrade to the more compact TOST Mini 150. To make this conversion, you'll need this cover, a TOST Mini wheel, and a set of washers. All required components are listed below.

This part can be adapted to fit the Discus-2a, Discus-2b, Discus-2c, Ventus-2ax, Ventus-2bx, the ventus-2c, the ventus-2cx and the Ventus-3.

It measures 148 mm in width. 

Please note that you will need to cut the part to ensure it fits your glider, as it is sold in an untrimmed form.

This cable is designed for the front seat of the Arcus, Duo Discus x, and Duo Discus xL equipped with a TOST wheel and a Magura cylinder brake.

The brake cable is 600 mm long, with a diameter of Ø1.5 mm, and is fitted with a 9 mm diameter nipple. The black segmented cable housing is included.

Please note, this cable is not compatible with the first-generation Duo Discus or the Arcus edition 2020, which are equipped, respectively, with master cylinder model 7 / brakes 30-9 and the BZT2 TOST brake system.

The EASA Form one is included.

This comprehensive kit ensures compatibility with all single-seater gliders equipped with drum brakes and provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 1600 mm of 2 mm cable with a 5.5 x 10 mm nipple
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST, with a “Magura” cylinder brake.

The brake cable measures 555 mm in length and features a 6 x 10 mm nipple.

 

 

These three brass bushes are used for the propellor stopper of the Ventus-3M and the Arcus M edition 2020. The bush in the centre is 8 x 1 x 9.3 mm and the two on the side are 8 x 1 x 6.7 mm.

They can be damaged by the spring and this creates some play in the stopper.

 

This butterfly nut is M10 (DIN 315) and it is used to secure the cockpit weights in all Schempp-Hirth single seaters (except the Ventus-3), the Nimbus, the Janus and some of the first Duo Discus.

This safety pin (or Fokker pin) is 1,5 mm and it is used to secure the cockpit weight in Schempp-Hirth gliders.

This O-ring  Ø32 x Ø3 is used for the water dump valve of several gliders:

• the Duo Discus x and xL,
• all the Arcus,
• some Discus-2c (the system has been upgraded in 2005),
• the Ventus-2cx and the Ventus-2cxa for the inner wing dump system not the outer wing.

This set of gasket can replace the on the main brake cylinder form 6 or 7. It is very likely that this type of cylinder is installed in the Duo Discus (but not in the x or xL), some Nimbus-4(D), as well as in some retrofitted Nimbus and Janus.

It do not work with the rectangular brake cylinder installed on some gliders (Ref: B40-1014). 

This knurled nut M10 DIN 467 is used to secure the cockpit weights of all the Ventus-3, the Arcus and some Duo Discus (xL).

It is sold with the safety pin (L01-0142)

This coupling is used for the fuel line going to the wing tank of the Ventus-3M and the Arcus M.

Please make sure you are entitled and have the skills to change that part. It should be secured with Loctite 577.

Please note: The coupling for the vent line is different. 

This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.

Its stopnut is included.

This is the castle nut is used for the main landing gear of all the Duo Discus and Arcus.

It is 8 mm, M14 x 1,5 DIN 937.

This lid is used for the cooler of all the Ventus-3M (Solo 2625-01i and 2625-01i neo) and all the Arcus M (Solo 2625-02i) after 2018 but not for the other version. 

Please note that if the radiator of your glider is not black, you might need a different lid. Please contact Spare Parts.

This item will allow you to replace the wing fuel tank of your Ventus-2cM and Ventus-2cxM.

 

This pin is 40 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and does not have an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, all Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.

This threaded rod is M8 and 186mm long.

It is use for the trim of the Duo Discus, Duo Discus xL, Arcus, Nimbus-4D and Nimbus-4DL. The system on the Arcus edition 2020 is different.

This bold is 6h11x28 mm, DIN 1434 / ISO 22341 and galvanized.

It is at the level of the pilot stick both front and back in the Duo Discus and the Nimbus-4D. With time, it can get rusty. 

It is sold here with its splint: 1,6 x 16, DIN 94 / ISO 1234 galvanized.

This washer is  16 x 2 x 5,5 mm and it is used for the tail wheel. 

These replacement springs are specifically designed for use with the BWS Flexiwiper system. Each set is sold as a matched pair, for the left and right Flexiwiper unit.

Important compatibility note:
These springs are not compatible with the Ventus-3 or Arcus edition 2020 Garagewipers models. 

This retrieval Line Dyneema is coated and talc-powdered.

The roll contain 25 m.

5 meter cleaning fialment are also provided !

The deflection pulley is used to eliminate friction from the Bowden cables (in mosquito cleaner systems) in the event of major directional changes of the cable to enable lower manual force/power consumption and faster cleaning.

From wing root to wing tip: The patented joint system adapts to the profile of the glider type during the cleaning process.

At a glance:

• A bug wiper for all types of glider.
• Aerodynamic shape.
• Streamlined, therefore minimum resistance.
• Fiber reinforced plastics with high strength.
• No buckling and no twisting of the components.
• UV-resistant.
• Double guided cleaning fialments: cleans efficiently and glides stably.
• Rests against the profile above and below the wings during the cleaning process.
• Fast mounting.

The BWS Flexiwiper can be retrofitted to almost any glider. For all Schempp-Hirth gliders, the retrival line is routed below the wing. Only this option is available in this shop. Before ordering for another type of glider, you have to consider whether the retrieval line is routed above or below the wing.

The package includes:

• 1 left and 1 right bug wiper inclusive fialments.
• 2 x tilt bracket to fit the fuselage.
• Installation manual.

You can find spare parts and related item below.

This item will allow you to replace the wing fuel tank of your Arcus.