Controls
-
elevator-trim blade spring for Arcus, all Duo Discus, all Nimbus-4D and all Discus
This spring is used for the trim of the Arcus, Duo Discus XL, Nimbus-4DL and all the Discus from the Discus a to the Discus-2c.
It is 25mm lage and the legs are 40mm long. The central part is 12,5mm.
Some glider need roll pins. They are not included but they can be baught individaly (see the suggested products).
from 1 € 4.65 incl. 19% VAT
€ 3.91 -
Roll pin for trim
Roll pin DIN 1481 / ISO 8752 stainless.
They are (mainly) used to in trim of the Arcus, Duo Discus XL and Nimbus-4DL.
There is two models : On gliders produced after April 2015, you will probably need the 2 x 16 mm model. For the older glider you will need to use the 2x14 mm roll pins. Please have a look in your glider to confirm which models you need.
from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Rod end bearing 14c6, M8 x 58
Rod end bearing with a 14c6 head and M8 x 58 length body.
Other rod end bearings are used in our gliders. If you are not sure which one you need. Please contact the Spare Part team.
from 1 € 25.14 incl. 19% VAT
€ 21.13 -
Schnorr-safety washer
Safety washers Form S available in M6 and M8.
These washers are used, among other things, to secure the rear part of the horizontal tail fitting and the elevator drive U-bracket.
from 1 € 0.48 incl. 19% VAT
€ 0.40 -
Automatic control connection for single seaters (exc. Ventus-3)
This bell crank is used on Discus b, Discus c, Discus-2a, -2b, -2c, Ventus b, Ventus c and Ventus-2a, -2b, -2c.
You may need to change them according to the TN 349-43.
You can buy the screws and bolts needed to change the part as an option. This option is currently un available but will be back within a few weeks.
from 1 € 373.60 incl. 19% VAT
€ 313.95 -
Fin tank valve for all single seaters (exc. Ventus-3)
This is the complete tank dump valve assembly. It is used for all single seaters except for the Ventus-3.
Arcus and Duo Discus xL have other model. See suggested products below. For first generation Duo Discus, Janus, Nimbus-3D and -4D, please contact our sparepart team.
from 1 € 213.13 incl. 19% VAT
€ 179.10 -
Fin tank valve for Arcus, Duo Discus xL and Nimbus-4DL
This is the complete tank dump valve assembly. It is used for Arcus, Duo Discus xL and Nimbus-4DL.
Single seaters have another model. See suggested products below. For first generation Duo Discus, Janus, Nimbus-3D and -4D, please contact our spare part team.
from 1 € 263.34 incl. 19% VAT
€ 221.29 -
Bellow V6-0052 for waterballasts
This flexible rubber boot is 63 x 39x 39 mm with a 10 mm and a 25 mm opening.
It is surrounding the ballast rod on the wing root of the Discus b, Ventus-2 (SN < 561), Discus-2a and Discus-2b (SN< 234) which have been produced before June 2009. However, some of these gliders might have been retrofitted with the newer system. You can see on the suggested product the other bellow.
It is used for the ballast system of the Nimbus-3, -3D, -4 and -4D. For the Nimbus, the bellow may need to be adapted by cutting the larger end.
It is also used as a sealing around the brake line when crossing the wheel box in all single seaters.
from 1 € 21.25 incl. 19% VAT
€ 17.86 -
Brake pads Beringer ZEA01
These pads are used for the Beringer brakes of the Ventus-2, Discus-2, Duo Discus XL and Arcus.
We advise you to replace the pads before the thickness of friction material reachs 1.5 mm. For more information, you can consult the maintenace manual from Beringer.
A package contains the two pads used for one wheel.
from 1 € 83.30 incl. 19% VAT
€ 70.00 -
Brake pads for Cleveland caliper 30-9
These brake lining (Tost p/n 075865) are used on brake assembly 30-9.
It can be mounted to 4′′, 5′′ and 6′′ disk brake wheels of the series Penta, Tria and Classic and on the original Cleveland brakes- wheel system.
Different system has been used and several TN have been approved. Please look carefully to your brakes and order similar brake pad.
from 1 € 72.08 incl. 19% VAT
€ 60.57 -
Nicopress-oval sleeve 1,5-2 mm
Nicopress-oval sleeve 1,5-2 mm, ref : NT281C-A or N° 28-1-C.
It is 10 x 6 x 4 mm.
from 1 € 0.30 incl. 19% VAT
€ 0.25 -
Nicopress-Stop sleeve 1,5-1,7mm
Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).
It is 5 x 5 x 5 mm.from 1 € 0.48 incl. 19% VAT
€ 0.40 -
Nicopress-Stop sleeve 2,5 mm
Nicopress-Stop sleeve 2,5 mm, NTG282G-100.
It is 10 x 9 x 6 mm.
from 1 € 0.67 incl. 19% VAT
€ 0.56 -
Nicopress-Stop sleeve 3,0-3,5 mm
Nicopress-Stop sleeve 3,0-3,5 mm, NT283M / n° 28-3-M.
It is 14 x 12 x 8 mm.
from 1 € 1.04 incl. 19% VAT
€ 0.87 -
Thimble 2,5 mm galvanized
Thimble 2,5 mm galvanized.
It is 27 x 15 x 5 mm.
from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Thimble 3,5 mm galvanized
Thimble 3,5 mm galvanized.
It is 32 x 17 x 6 mm.
from 1 € 0.94 incl. 19% VAT
€ 0.79 -
Control cable A 1,6 mm
Control cable A, 1.6 mm, ISO 2020 (1/16”), DIN 3051 compliant, 7x7 construction
Sold by the meter.
This cable is often used for the turbo engine decompression system and fin tank control. Please refer to your maintenance manual to determine the correct cable type and connection instructions.
It is also commonly used for rudder pedal adjustment. For this application, we recommend purchasing the "Kit for rudder pedal adjustment ".
from 1 € 4.49 incl. 19% VAT
€ 3.77 -
Leg springs for water dump system for Arcus, Duo Discus XL and Ventus-2cx
This pair of leg springs is used for the Arcus, Duo Discus xL and Ventus-2cx.
Each spring is 101,5 mm long and 21 mm large.
from 1 € 14.04 incl. 19% VAT
€ 11.80
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.