The clamp is suitable for hoses with diameters ranging from 12 mm to 20 mm. It is specifically used in the fuel system of the Arcus M and Arcus T.

The clamp is suitable for hoses with diameters ranging from 6 mm to 7 mm and is used on some gliders for the rudder pedal cable.

These hinges are used to fix the landing gear door of almost all single seater.

Their dimensions are: 30 x 30 x 0,8 mm

The countersunk screws (fuselage side) and countersunk-head rivet with their washers (door side) can be ordered as an option.

This tension spring (ref RZ-124) is used in the rudder pedal of the Arcus, Duo Discus, and Nimbus-4D gliders, in the rear position, with two springs installed per glider. It is also used for the doors of the engine box in single seater.

The tension spring Z-109AI is used for the single seater landing gear doors.

Its dimensions are 77 x 11 x 11 mm

Tension Spring for the Discus-2 Trim System, Part No.: RZ-123 I

Tension spring for the trim system of the Discus-2 series. 3 springs are required per aircraft.

It is  Ø 1,6 x 14,1 x 59 mm

 

This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM, all Arcus M, all Ventus-3M and the Quintus.

The head is 10 mm and the screw 10 mm. Its head diameter is 24 mm. Look at the model(s) that you want to replace and order the same.

This high-quality, flexible shrink tubing is used for insulation and protection of cables and connections – including many fuel lines and some electronic components.

Minimum diameter before shrinking: 12.7 mm

Diameter after shrinking: 6.4 mm

It is sold by the meter.

This pushrod guide ball cage measures 25 × 3 × 20 mm.

Please note that another model exists with dimensions 29 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This screw is mainly used to secure the rear part of the horizontal tail fitting.

This perspex disc is made for Arcus, all Duo Discus, Ventus-3, Discus-2b, -2c, Discus b and cs.

However, some gliders have more than one perspex disc and they can be different. Please look at the diameter and model you need.

Its diameter is 78,3 mm and the central hole is 5 mm.

Two models exist, with or without a base, please choose the model who is already on your glider.

They are 10 mm high.

They are sold individually but you will need 5 of them for your glider.

This fuel filter Karcoma 99.106/8-100 is used for the refuelling and fuel hoses.

It is 80 mm long and its diameter is 30 mm.

This 6k-Screw is used for the airbrake drive funnel of the Ventus-2 and Discus-2c.

This piece is used to protect the spark plug from the rain in the SOLO 2350 engine.

SOLO spare part n° 00 84 203

This pushrod guide ball cage measures 29 × 3 × 20 mm.

Please note that another model exists with dimensions 25 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This connection fitting is used, sometime, to the Polyflex hose of the classic Duo Discus which are using the Classic wheel from TOST with a Magura cylinder brake.

This rubber ring is Ø80 x Ø10 and it is the tire of the wing wheel Lindner of the Arcus.

This spring is used for the trim of the Arcus, Duo Discus XL, Nimbus-4DL and all the Discus from the Discus a to the Discus-2c.

It is 25mm lage and the legs are 40mm long. The central part is 12,5mm.

Some glider need roll pins. They are not included but they can be baught individaly (see the suggested products). 

This bowden cable is 5,3 x 4,4 x 3,0 mm. It can also be referred to as 5.51.0000.022.

It is 80 cm and includes 2 cable end caps. To order a bigger quantity see the 

This cable is often used for the wheel brake systems. Please refer to your maintenance manual for the type of cable you need and how to make the connections.

 

This tension spring is 1,02 x 11 x 72 mm.

It is used for the arresting cables of the Ventus-2cT, -2cxT and Discus-2cT with engine Solo 2350.

 

The tension spring is used for the retraction of the landing gear of all the Discus, Discus-2, Ventus, Ventus-2 and the Nimbus-4.

Its dimensions are 1,6 x 12,7 x 164,5 mm.

This tension spring (ref. S-4640) is used in the turbo box of the Arcus T, Arcus T edition 2020, Duo Discus T, and Duo Discus xLT.

This spark plug is used for all SOLO engines.

These springs are used for the water dump system on the Mini-Nimbus, Duo Discus, Ventus-2c and Ventus 3.

It is 99,5 mm long and the diameter of the coiled is 15 mm. The steel wire diameter is 1,5 mm.

This service applies when our team enters an order by phone on the customer’s behalf. It is used only in special cases where personal assistance is required. 

This bushing is Ø16x3x24,1.

It is used for the engine bearing of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM

These washers are 14x9,8x0,5 mm.

They are made for the wing bolt that have a 10 mm diameter. This includes the wing extension bolt of all Arcus, all Duo Discus, the Nimbus-3, -3D, -4 and -4D, the Janus, the Discus-b, the Discus-2a and -2b and the Ventus c. It is also the case for the winglet bolt of the Discus, the Standard Cirrus, the Ventus-2a and the Ventus-2b.

These washers internal diameter is 9,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

They are sold in a kit of 4.

This bowden cable is 5,3 x 4,4 x 3,0 mm. It can also be referred to as 5.51.0000.022.

It is sold by the meter and includes 2 cable end caps.

This cable is often used for the wheel brake systems. Please refer to your maintenance manual for the type of cable you need and how to make the connections.

Stainless steel fork head (clevis) with a 4 mm pin diameter and a 16 mm fork width, manufactured in accordance with DIN 71752.

It is used in the fuel actuation system of the Duo Discus T, Duo Discus xT, Duo Discus xLT, Arcus T, Arcus 20 T, Arcus 20 M, and Ventus-3M Neo.

This knurled nut M10 DIN 467 is used to secure the cockpit weights of all the Ventus-3, the Arcus and some Duo Discus (xL).

It is sold with the safety pin (L01-0142)

This plate in grey PVC is used as a guide for all single-seater landing gear (except for the Ventus-3).

Its length is 220 x 24 mm and there is no hole. Adjust it to your glider.

Gasket for the canopy frame of single-seat gliders, sold by the metre.

Please note: some gliders have this gasket on one side only, with a different seal on the other side (the one used for the two-seaters, see recommanded product). Please check your glider carefully before ordering.

This indexing plunger without lock is used for the adjustment mechanism of the headset position in all Arcus M models, and for the oxygen bottle mount in the Arcus Edition 2020 and Ventus-3.

This washer DIN 9021 M8, 8,4 bright countersunk is mainly use to fix the O2-bottle holder when the holder is over the spar bridge.

This 6k-Screw is mainly used at the rear part of the horizontal tail fitting.
 

This MPX-PIK male cable (cross-section 2.5 mm², length 30 cm) connects the most of the modern glider’s electrical system to a battery equipped with an MPX female connector.

SOLO Silent block bush, spare part n° 20 61 395

 

This plug is used for the Ventus-3M and the Arcus M Edition 2020.

This bushing is Ø13x1,5x34,5.

It is used for the rear spindle suspension of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM