This Polyflex brake hose fit the classic Duo Discus equipped with a master cylinder model 7 / brakes 30-9. 

It is 600 mm lenght.

This pushrod guide ball cage measures 25 × 3 × 20 mm.

Please note that another model exists with dimensions 29 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This pushrod guide ball cage measures 29 × 3 × 20 mm.

Please note that another model exists with dimensions 25 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

It is used in the trim system of the Arcus, Duo Discus, Nimbus-4, and Nimbus-4D gliders, in the rear position, with two springs installed per glider.

This flexible rubber boot is 63 x 39x 39 mm with a 10 mm and a 25 mm opening.

It is surrounding the ballast rod on the wing root of the Discus b, Ventus-2 (SN < 561), Discus-2a and Discus-2b (SN< 234) which have been produced before June 2009. However, some of these gliders might have been retrofitted with the newer system. You can see on the suggested product the other bellow.

It is used for the ballast system of the Nimbus-3, -3D, -4 and -4D. For the Nimbus, the bellow may need to be adapted by cutting the larger end.

It is also used as a sealing around the brake line when crossing the wheel box in all single seaters.

 

These brake lining (Tost p/n 075865) are used on brake assembly 30-9.

It can be mounted to 4′′, 5′′ and 6′′ disk brake wheels of the series Penta, Tria and Classic and on the original Cleveland brakes- wheel system.

Different system has been used and several TN have been approved. Please look carefully to your brakes and order similar brake pad.

Nicopress-oval sleeve 1,5-2 mm, ref : NT281C-A or N° 28-1-C.

It is 10 x 6 x 4 mm.

Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).

It is 5 x 5 x 5 mm.

Nicopress-Stop sleeve 2,5 mm, NTG282G-100.

It is 10 x 9 x 6 mm.

Nicopress-Stop sleeve 3,0-3,5 mm, NT283M / n° 28-3-M.

It is 14 x 12 x 8 mm.

Thimble  2,5 mm galvanized.

It is 27 x 15 x 5 mm.

Thimble  3,5 mm galvanized.

It is 32 x 17 x 6 mm.

This rubber boot is surrounding the water ballast control rod to avoid the water leaking through. It is used in several Schempp-Hirth gliders including the Nimbus-2, Ventus, Ventus-2c, Discus-2c, Duo Discus and the Arcus.

It is 125 x 22 x 22 mm with a 7 mm and a 16 mm opening.

Over the years, other bellows and different combinations have been used. You can find them underneath this description, in the "suggested products", if you want to compare them with the model that you wish to replace.

This pair of leg springs is used for the Arcus, Duo Discus xL and Ventus-2cx.

Each spring is 101,5 mm long and 21 mm large.

These springs are used for the water dump system on the Mini-Nimbus, Duo Discus, Ventus-2c and Ventus 3.

It is 99,5 mm long and the diameter of the coiled is 15 mm. The steel wire diameter is 1,5 mm.