The clamp is suitable for hoses with diameters ranging from 12 mm to 18 mm and is used on some gliders for the water ballast system in the wing.

This foil sealing ring has a diameter of 95 mm and is used to cover the handhole cap of the Duo Discus, Arcus, Discus-2b, Discus-2c, Discus b, Discus cs und Ventus-3 and Ventus-3.

This deep groove ball bearing (6804-2RS, 20E1, DIN 625) is 20 mm inner diameter, 32 mm outer dimeter, 7 mm width, with seals on both sides. 

It is used for the rear part of the horizontal tailplane fitting (item B40-0824), serving as a bearing support for the airbrake drive shaft.

This pin is 84 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and has an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.

This washer is used to adjust the distance between the wing and the fuselage. It is 0.3 mm thick.

They fit an 18 mm wing bolt, including both the front and rear bolts at the wing root of two-seater aircraft.

The washers have an internal diameter of 17.8 mm. They are slightly smaller than the bolt to ensure they stay in place when installed.

A kit containing eight washers with a thickness of 0.5 mm and four washers with a thickness of 0.8 mm is also available.

This spring is designed for the airbrakes of all Schempp-Hirth gliders ecxcept the Ventus-3.

The spring is 1 x 10 x 30 mm.

Depending on your glider model, each airbrake may require 2 of these springs.

Important Note: This spring is used on the outside of the airbrakes. The other spring are straight (ref L03-0033). You can find them among our suggested products.

This spring is designed for the airbrakes of all Schempp-Hirth gliders.

The spring is 0.8 mm x 7.8 mm x 30 mm.

Depending on your glider model, each airbrake may require between 9 and 11 of these springs.

Important Note: The exterior springs often differ from this ones. You can find the suitable exterior springs (ref L03-0032) among our suggested products.

 

This O-ring  Ø32 x Ø3 is used for the water dump valve of several gliders:

• the Duo Discus x and xL,
• all the Arcus,
• some Discus-2c (the system has been upgraded in 2005),
• the Ventus-2cx and the Ventus-2cxa for the inner wing dump system not the outer wing.

This pin is 40 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and does not have an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, all Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.

These springs are uses for the BWS flexiwiper. 

We sell them as a pair to replace the top and bottom springs of one Flexiwiper.

This retrieval Line Dyneema is coated and talc-powdered.

The roll contain 25 m.

5 meter cleaning fialment are also provided !

The deflection pulley is used to eliminate friction from the Bowden cables (in mosquito cleaner systems) in the event of major directional changes of the cable to enable lower manual force/power consumption and faster cleaning.

From wing root to wing tip: The patented joint system adapts to the profile of the glider type during the cleaning process.

At a glance:

• A bug wiper for all types of glider.
• Aerodynamic shape.
• Streamlined, therefore minimum resistance.
• Fiber reinforced plastics with high strength.
• No buckling and no twisting of the components.
• UV-resistant.
• Double guided cleaning fialments: cleans efficiently and glides stably.
• Rests against the profile above and below the wings during the cleaning process.
• Fast mounting.

The BWS Flexiwiper can be retrofitted to almost any glider. For all Schempp-Hirth gliders, the retrival line is routed below the wing. Only this option is available in this shop. Before ordering for another type of glider, you have to consider whether the retrieval line is routed above or below the wing.

The package includes:

• 1 left and 1 right bug wiper inclusive fialments.
• 2 x tilt bracket to fit the fuselage.
• Installation manual.

You can find spare parts and related item below.

This system is fast, reliable and easy to install in your glider. 

The main features are:

• Short cleaning time of approx. 15 seconds per wing (even at high speeds).
• Simultaneous cleaning with both bug wipers possible.
• Three safety features: rope tension sensor, slip clutch and automatic shutdown on overload.
• Tear-resistant Dyneema line (retrieval line).
• Span adjustment (optionnal, please contact us).
• It is sold here with the mounting type 1, the most versatil one. However, if you want to install the winch near the feet of the backseat pilot, you may want to look also to the mounting plate Nr. 3 and Nr. 4.

It is delivered with:

• 2 x BWS electric winches in the box
• 2 x mounting plate no. 1
• 2 x Double switch for instrument panel mounting
• Installation kit double seater
• Installation and operating manuals

You can find spare parts, other mounting plates and related items below.

This system is fast, reliable and easy to install in your glider. 

The main features are:

• Short cleaning time of approx. 15 seconds per wing (even at high speeds).
• Simultaneous cleaning with both bug wipers possible.
• Three safety features: rope tension sensor, slip clutch and automatic shutdown on overload.
• Tear-resistant Dyneema line (retrieval line).
• Span adjustment (optional, please contact us).
• It is sold here with the mounting type 1, the most versatil one, but a large variety of plates are available for easy and flexible installation.

It is delivered with:

• 2 x BWS electric winches in the box
• 2 x mounting plate no. 1 - Suitable for almost all aircraft and installation positions. Special mounting slides (e.g. for Arcus) are also available.
• Double switch for instrument panel mounting
• Installation kit single seater
• Installation and operating manual

You can find spare parts, other mounting plates and related items below.

The simple and proven solution for your bug wriper.

With its integrated damping system, it offers a smooth-run.

It is delivered with:

• 2 pieces BWS crank handles
• Mounting plate
• Installation kit
• Installation and operating manuals

You can find spare parts and related item below.

These bug-wipers blades are adapted for all the Ventus-3 variants and the Arcus Edition 2020 with garage for bug-wipers.

This plexi cover is made for the Janus, the Ventus b and some Ventus-2. It is used in the TN 349-42 / 825-57.

Its diameter is 53,5 mm and the central hole is 5 mm. The locking device is 100mm long.

 

This sealing lid is for the Arcus edition 2020.

It is equipped of a non-return valve.