These washers are 14x9,8x0,5 mm.

They are made for the wing bolt that have a 10 mm diameter. This includes the wing extension bolt of all Arcus, all Duo Discus, the Nimbus-3, -3D, -4 and -4D, the Janus, the Discus-b, the Discus-2a and -2b and the Ventus c. It is also the case for the winglet bolt of the Discus, the Standard Cirrus, the Ventus-2a and the Ventus-2b.

These washers internal diameter is 9,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

They are sold in a kit of 4.

This flexible rubber boot is 63 x 39x 39 mm with a 10 mm and a 25 mm opening.

It is surrounding the ballast rod on the wing root of the Discus b, Ventus-2 (SN < 561), Discus-2a and Discus-2b (SN< 234) which have been produced before June 2009. However, some of these gliders might have been retrofitted with the newer system. You can see on the suggested product the other bellow.

It is used for the ballast system of the Nimbus-3, -3D, -4 and -4D. For the Nimbus, the bellow may need to be adapted by cutting the larger end.

It is also used as a sealing around the brake line when crossing the wheel box in all single seaters.

 

This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.

These roll pins are used to secure the aileron.

Dimension: 2 x 10 mm

DIN 1481 / ISO 8752

This drive funnel is used on almost all Schempp-Hirth gliders except the Nimbus-4 and the Ventus-3.

Two lock nuts M 6-8, DIN 985 and a lock nut M6 TRELOC, DIN 439 are included. However, your glider has a specific set of distance washer that are not provided. Please before disassemble the funnel make sure you know which washer go where.

On the Ventus-2 and Discus-2c, you may also need a set of screws that can be baught as an option.

These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.

They fit a 18 mm wing bolt. That includes the front and back bolts at the wing root of the double seaters.

These washers internal diameter is 17,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.

They fit a 14 mm wing bolt. That includes the front and back bolts at the wing root of almost all the single seaters as well as the wing extention bolt of the Discus-2c, Ventus-2c and Ventus-3 and some winglet bolts.

These washers internal diameter is 13,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

This spherical bearing is adapted for 18mm diameter pin of the double seaters.

The internal diameter is 18 mm and the part is 32x32x14 mm.

This spherical bearing is adapted for 14mm diameter pin of the single seaters.

The internal diameter is 14 mm and the part is 25x25x8-11 mm.

 

The visible part of the peg is 70,5 mm long with a 14 mm diameter. The internal part is 35 mm long, with a 40 mm diameter.

It is used on the back part of the Discus-2c and Ventus-2c wing roots.

The visible part of the pin is 38,5 mm long with a 14 mm diameter. The inner part is 35 mm long and has a diameter of 40 mm.

It is used on the wing roots front part of the Discus, Discus-2, Ventus, Ventus-2c and Ventus-3S.

The visible part of the peg is 78,5 mm long and has a diameter of 18 mm. The inner part is 42 mm long and has a diameter of 40 mm.

It is used on the wing roots back part of the Nimbus-3D, the Nimbus-4D, the Duo Discus and the Arcus. It is not adapted for the Janus.

 

The visible part of the pin is 48 mm long and has a diameter of 18 mm. The inner part is 42 mm long and has a diameter of 40 mm.

It is used on the wing roots front part of the double seaters as well as for the front and rear roots of the Janus.