Wing
-
Water filler cap
This sealing cap is for the Ventus-2, Discus-2, Duo Discus and the first Arcus.
The cap diameter is 36 mm and it is 5 mm high with a M6 hole on the side (B40-1226). Older gliders can have the same cap but the system may be different.
For a clean fit, the cover should be adjusted by grinding the profile contour.
from 1 € 52.32 incl. 19% VAT
€ 43.97 -
Water filler cap top
This plug is 5 mm high and its diameter is 36 mm. It fit all the Ventus 2, Discus 2, Nimbus 3, Duo Discus and the first Arcus.
Dependant on the glider, older Ventus and Discus can need this model or a 35 mm diameter sealing cap that is 7,5 mm high. Please look at your current model to order the same. If you need the thick sealing cap, you can order it through Schempp-Hirth spare-part form.
For a clean fit, the cover should be adjusted by grinding the profile contour.
from 1 € 9.64 incl. 19% VAT
€ 8.10 -
Shim washer for 10 mm diameter wing bolt
These washers are 14x9,8x0,5 mm.
They are made for the wing bolt that have a 10 mm diameter. This includes the wing extension bolt of all Arcus, all Duo Discus, the Nimbus-3, -3D, -4 and -4D, the Janus, the Discus-b, the Discus-2a and -2b and the Ventus c. It is also the case for the winglet bolt of the Discus, the Standard Cirrus, the Ventus-2a and the Ventus-2b.
These washers internal diameter is 9,8 mm. They are a bit smaller than the pin in order to stay in place when installed.
They are sold in a kit of 4.
from 1 € 5.05 incl. 19% VAT
€ 4.24 -
Bellow V6-0052 for waterballasts
This flexible rubber boot is 63 x 39x 39 mm with a 10 mm and a 25 mm opening.
It is surrounding the ballast rod on the wing root of the Discus b, Ventus-2 (SN < 561), Discus-2a and Discus-2b (SN< 234) which have been produced before June 2009. However, some of these gliders might have been retrofitted with the newer system. You can see on the suggested product the other bellow.
It is used for the ballast system of the Nimbus-3, -3D, -4 and -4D. For the Nimbus, the bellow may need to be adapted by cutting the larger end.
It is also used as a sealing around the brake line when crossing the wheel box in all single seaters.
from 1 € 21.25 incl. 19% VAT
€ 17.86 -
Safety ring-spring steel, DIN471, size 8
This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.from 1 € 0.55 incl. 19% VAT
€ 0.46 -
Roll pin for aileron
These roll pins are used to secure the aileron.
Dimension: 2 x 10 mm
DIN 1481 / ISO 8752
from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Automatic control connection for single seaters (exc. Ventus-3)
This bell crank is used on Discus b, Discus c, Discus-2a, -2b, -2c, Ventus b, Ventus c and Ventus-2a, -2b, -2c.
You may need to change them according to the TN 349-43.
You can buy the screws and bolts needed to change the part as an option. This option is currently un available but will be back within a few weeks.
from 1 € 373.60 incl. 19% VAT
€ 313.95 -
Airbrake drive funnel
This drive funnel is used on almost all Schempp-Hirth gliders except the Nimbus-4 and the Ventus-3.
Two lock nuts M 6-8, DIN 985 and a lock nut M6 TRELOC, DIN 439 are included. However, your glider has a specific set of distance washer that are not provided. Please before disassemble the funnel make sure you know which washer go where.
On the Ventus-2 and Discus-2c, you may also need a set of screws that can be baught as an option.
from 1 € 258.12 incl. 19% VAT
€ 216.91 -
Shim washer kit for 18 mm wing bolt
These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.
They fit a 18 mm wing bolt. That includes the front and back bolts at the wing root of the double seaters.
These washers internal diameter is 17,8 mm. They are a bit smaller than the pin in order to stay in place when installed.
from 1 € 24.42 incl. 19% VAT
€ 20.52
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.