The visible part of the pin is 38,5 mm long with a 14 mm diameter. The inner part is 35 mm long and has a diameter of 40 mm.

It is used on the wing roots front part of the Discus, Discus-2, Ventus, Ventus-2c and Ventus-3S.

The visible part of the peg is 78,5 mm long and has a diameter of 18 mm. The inner part is 42 mm long and has a diameter of 40 mm.

It is used on the wing roots back part of the Nimbus-3D, the Nimbus-4D, the Duo Discus and the Arcus. It is not adapted for the Janus.

 

The visible part of the pin is 48 mm long and has a diameter of 18 mm. The inner part is 42 mm long and has a diameter of 40 mm.

It is used on the wing roots front part of the double seaters as well as for the front and rear roots of the Janus.

This skid is 121 x 35 x 28,5 mm and is used for Discus a, Discus b, Ventus b, Ventus c and all the Ventus-2.

Double face tape is already fixed on the skid to instal it easily.

This skid is 164 x 48 x 36 mm is used for the Discus-2a, -2b and 2-c.

Double face tape is already fixed on the skid to instal it easily.

This retrieval Line Dyneema is coated and talc-powdered.

The roll contain 25 m.

5 meter cleaning fialment are also provided !

This spherical bearing is adapted for 14mm diameter pin of the single seaters.

The internal diameter is 14 mm and the part is 25x25x8-11 mm.

 

This sealing cap is made for the Ventus-3 outer wing.

The plug used for the inner wing is different. You can find it below in the suggested items.

Please note that the first seven Ventus-3 are equipped with a different system.

This tool allows you to assemble Discus-2c, Ventus-2c and Ventus-3 wing extensions.

These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.

They fit a 18 mm wing bolt. That includes the front and back bolts at the wing root of the double seaters.

These washers internal diameter is 17,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

The Schempp-Hirth iconic tool with an extra pin to dismantle the wingtip.

This sealing cap is made for the Ventus-3 inner wing.

The plug used for the outer wing is different. You can find it below in the suggested items.

Please note that the first seven Ventus-3 are equipped with a different system.

This rubber boot is surrounding the water ballast control rod to avoid the water leaking through. It is used in several Schempp-Hirth gliders including the Nimbus-2, Ventus, Ventus-2c, Discus-2c, Duo Discus and the Arcus.

It is 125 x 22 x 22 mm with a 7 mm and a 16 mm opening.

Over the years, other bellows and different combinations have been used. You can find them underneath this description, in the "suggested products", if you want to compare them with the model that you wish to replace.

This flexible rubber boot is 63 x 39x 39 mm with a 10 mm and a 25 mm opening.

It is surrounding the ballast rod on the wing root of the Discus b, Ventus-2 (SN < 561), Discus-2a and Discus-2b (SN< 234) which have been produced before June 2009. However, some of these gliders might have been retrofitted with the newer system. You can see on the suggested product the other bellow.

It is used for the ballast system of the Nimbus-3, -3D, -4 and -4D. For the Nimbus, the bellow may need to be adapted by cutting the larger end.

It is also used as a sealing around the brake line when crossing the wheel box in all single seaters.

 

These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.

They fit a 14 mm wing bolt. That includes the front and back bolts at the wing root of almost all the single seaters as well as the wing extention bolt of the Discus-2c, Ventus-2c and Ventus-3 and some winglet bolts.

These washers internal diameter is 13,8 mm. They are a bit smaller than the pin in order to stay in place when installed.

This spherical bearing is adapted for 18mm diameter pin of the double seaters.

The internal diameter is 18 mm and the part is 32x32x14 mm.

This perspex disc is made for the Ventus-2a.

Its diameter is 53,5 mm and the central hole is 5 mm.