This fiberglass bracket is designed for 7.5 Ah battery holders.

It has a width of 38 mm and fits a 97 mm battery. The shape is straight. 

A similar model (F60-0651) features a bend and is used in several gliders, including the Duo Discus XL and the Arcus. Please check the model installed in your glider carefully before purchasing.

These brake linings (Tost P/N 080949) are designed for the BZT2 brake assembly installed after 2017 with a thread M10x1. It is not compatible with the model with a thread NPT See drawing.

The BZT2 system is compatible with 5″ and 6″ disc brake wheels from the Penta and Classic series. It is commonly installed on the Ventus-3 and Arcus edition 2020 models.

Please note that different braking systems have been used over time, and several Technical Notices (TN) have been approved. Carefully inspect your brakes before ordering to ensure you select the correct brake pad.

Thesef felt rings measure 20x10 mm and are 3 mm thick. They are designed for 14 C6 bearings.

Please note that a thinner model (L07-0594) is used for 10 C6 bearings.

This throttle valve sensor mounted (Solo part number 23 00 910) is used in the Solo 2625 01i, Solo 2625 01i Neo and 2625 02i.

 

This hose set is designed for use with the Solo 2625 02 and 02i engines in the Arcus M and Arcus M edition 2020 gliders.

This 2520 Poly Chain GT2 toothed belt is designed for the pylon of the Nimbus-4M and Nimbus-4DM equipped with a Solo engine 2625.

This high-quality, flexible shrink tubing is used for insulation and protection of cables and connections – including many fuel lines and some electronic components.

Minimum diameter before shrinking: 12.7 mm

Diameter after shrinking: 6.4 mm

It is sold by the meter.

This support is used for the lower rudder of the Arcus M.

The EASA Form one is included.

This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.

 

This propeller brake pad is designed for the propellers of the almost all the Ventus-2cM, Ventus-3M, and all Arcus M models.

Some Nimbus-4M and Nimbus-4DM gliders may also be equipped with this system if Technical Note 868-19 has been applied.

This brass bushing (13x1.5x6.5 mm) is used on the front elevator mount of the Standard Cirrus.

 

This washer is used to adjust the distance between the wing and the fuselage. It is 0.3 mm thick.

They fit an 18 mm wing bolt, including both the front and rear bolts at the wing root of two-seater aircraft.

The washers have an internal diameter of 17.8 mm. They are slightly smaller than the bolt to ensure they stay in place when installed.

A kit containing eight washers with a thickness of 0.5 mm and four washers with a thickness of 0.8 mm is also available.

This is a 3,2 washer DIN 9021 / ISO 7093-1 galvanized.

This pin is 84 mm long, conforms to DIN 1434 / ISO 22341, has a small head, and has an eye.

It is used for the aileron bearing of several gliders, including the Discus-2, Ventus-2, Ventus-3, Duo Discus and Arcus. Various types of axles and pins are used for each ailerons, so please make sure to carefully check which ones you need.

This is a galvanized, spring-loaded, self-locking hex nut in M10 size, manufactured to the SSB 003 specification with an FK4 flat design and a 17 mm wrench size.

It is used on the landing gear of nearly all Schempp-Hirth gliders, for the shock absorber and/or the drag strut.

The clamp is suitable for hoses with diameters ranging from 6 mm to 7 mm and is used on some gliders for the rudder pedal cable.

This slip joint is used in the exhaust system of the Solo 2625-01i, 2625-01i Neo, 2625-02i and 2625-02i Neo engines, which are installed in the Ventus-3 and the Arcus gliders.

It is the Solo spare part 25 00 850.

This deep groove ball bearing (6804-2RS, 20E1, DIN 625) is 20 mm inner diameter, 32 mm outer dimeter, 7 mm width, with seals on both sides. 

It is used for the rear part of the horizontal tailplane fitting (item B40-0824), serving as a bearing support for the airbrake drive shaft.

This Master Cylinder Model 7 is used on the older Duo Discus and Nimbus-4D aircraft equipped with 30-9 brakes.