This bold is 6h11x28 mm, DIN 1434 / ISO 22341 and galvanized.

It is at the level of the pilot stick both front and back in the Duo Discus and the Nimbus-4D. With time, it can get rusty. 

It is sold here with its splint: 1,6 x 16, DIN 94 / ISO 1234 galvanized.

This threaded rod is M8 and 186mm long.

It is use for the trim of the Duo Discus, Duo Discus xL, Arcus, Nimbus-4D and Nimbus-4DL. The system on the Arcus edition 2020 is different.

This set of gasket can replace the on the main brake cylinder form 6 or 7. It is very likely that this type of cylinder is installed in the Duo Discus (but not in the x or xL), some Nimbus-4(D), as well as in some retrofitted Nimbus and Janus.

It do not work with the rectangular brake cylinder installed on some gliders (Ref: B40-1014). 

This O-ring  Ø32 x Ø3 is used for the water dump valve of several gliders:

• the Duo Discus x and xL,
• all the Arcus,
• some Discus-2c (the system has been upgraded in 2005),
• the Ventus-2cx and the Ventus-2cxa for the inner wing dump system not the outer wing.

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST, with a “Magura” cylinder brake.

The brake cable measures 555 mm in length and features a 6 x 10 mm nipple.

 

 

This comprehensive kit ensures compatibility with all single-seater gliders equipped with drum brakes and provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 1600 mm of 2 mm cable with a 5.5 x 10 mm nipple
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

This cable is designed for the front seat of the Arcus, Duo Discus x, and Duo Discus xL equipped with a TOST wheel and a Magura cylinder brake.

The brake cable is 600 mm long, with a diameter of Ø1.5 mm, and is fitted with a 9 mm diameter nipple.

Please note, this cable is not compatible with the first-generation Duo Discus or the Arcus edition 2020, which are equipped, respectively, with master cylinder model 7 / brakes 30-9 and the BZT2 TOST brake system.

The EASA Form one is included.

This part can be adapted to fit the Discus-2a, Discus-2b, Discus-2c, Ventus-2ax, Ventus-2bx, the ventus-2c, the ventus-2cx and the Ventus-3.

It measures 148 mm in width. 

Please note that you will need to cut the part to ensure it fits your glider, as it is sold in an untrimmed form.

This comprehensive kit ensures compatibility with all Duo Discus equipped with a master cylinder model 7 / brakes 30-9. It provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 4000 mm of 1,8 mm cable
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

This part can be adapted to fit the Duo Discus, Duo Discus X, Duo Discus XL, as well as the Arcus, Arcus Edition 2020, and Nimbus-4D.

It measures approximately 147 mm in width and 157 mm in length.

Please note that the part is sold in an untrimmed form, so you will need to cut it to ensure a proper fit for your glider.

This slotted hexagonal-head nut, M8, DIN 14441 is copper plated  and is commonly used for rudder fixation.

These brake linings (Tost P/N 080949) are designed for the BZT2 brake assembly installed after 2017 with a thread M10x1. It is not compatible with the model with a thread NPT See drawing.

The BZT2 system is compatible with 5″ and 6″ disc brake wheels from the Penta and Classic series. It is commonly installed on the Ventus-3 and Arcus edition 2020 models.

Please note that different braking systems have been used over time, and several Technical Notices (TN) have been approved. Carefully inspect your brakes before ordering to ensure you select the correct brake pad.

Thesef felt rings measure 20x10 mm and are 3 mm thick. They are designed for 14 C6 bearings.

Please note that a thinner model (L07-0594) is used for 10 C6 bearings.

This high-quality, flexible shrink tubing is used for insulation and protection of cables and connections – including many fuel lines and some electronic components.

Minimum diameter before shrinking: 12.7 mm

Diameter after shrinking: 6.4 mm

It is sold by the meter.

This brass bushing (13x1.5x6.5 mm) is used on the front elevator mount of the Standard Cirrus.

 

This is a galvanized, spring-loaded, self-locking hex nut in M10 size, manufactured to the SSB 003 specification with an FK4 flat design and a 17 mm wrench size.

It is used on the landing gear of nearly all Schempp-Hirth gliders, for the shock absorber and/or the drag strut.

The clamp is suitable for hoses with diameters ranging from 6 mm to 7 mm and is used on some gliders for the rudder pedal cable.

This deep groove ball bearing (6804-2RS, 20E1, DIN 625) is 20 mm inner diameter, 32 mm outer dimeter, 7 mm width, with seals on both sides. 

It is used for the rear part of the horizontal tailplane fitting (item B40-0824), serving as a bearing support for the airbrake drive shaft.

This Master Cylinder Model 7 is used on the older Duo Discus and Nimbus-4D aircraft equipped with 30-9 brakes.

 

This tension spring is used to hold the flap handle in the correct position.

It was originally used on the Janus C, Nimbus-3D, and Nimbus-4D, and is located on the rear cockpit wall (back seat).

However, some gliders have been modified and now use a flat spring (Ref. B40-0297) mounted near the spar bridge.

This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.

Polyflex-hose is 1004 CK and it is 1080mm.