These eyelet is used for the landing gear doors for all models.

Stainless steel fork head (clevis) with a 4 mm pin diameter and a 16 mm fork width, manufactured in accordance with DIN 71752.

It is used in the fuel actuation system of the Duo Discus T, Duo Discus xT, Duo Discus xLT, Arcus T, Arcus 20 T, Arcus 20 M, and Ventus-3M Neo.

Ring tongue terminal with closed barrel

• Stud size: M6 (≈ 6.73 mm)
• Wire range: 14 AWG (≈ 2 mm²)
• Insulation: Blue, partially insulated sleeve

Applications:

• Electrical power systems
• Ground connection on the wing fuel tank
• Ground connection on the nose

This WK 21 filter is used for the pitot tube in the glider’s nose.

This foil sealing ring has a diameter of 95 mm and is used to cover the handhole cap of the Duo Discus, Arcus, Discus-2b, Discus-2c, Discus b, Discus cs und Ventus-3 and Ventus-3.

This Polyflex brake hose fits the classic Duo Discus equipped with master cylinder model 7 and 30-9 brakes.

The hose length is 600 mm.

Depending on your glider configuration, you may also require two adapters, which can be found under recommended products (references: L07-1346 and L07-0406).

This Trim weight is 3,7 kg and it is used for the Arcus, Duo Discus and Janus.

This indexing plunger without lock is used for the adjustment mechanism of the headset position in all Arcus M models, and for the oxygen bottle mount in the Arcus Edition 2020 and Ventus-3.

This Elesa knurled head screw (M6x16) is used for various functions, including the adjustment mechanism of the headset position.

This pulley with 626-ZZ bearing is used for the hook release mechanism and for some turbo actuation systems.

This pushrod guide ball cage measures 25 × 3 × 20 mm.

Please note that another model exists with dimensions 29 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This pushrod guide ball cage measures 29 × 3 × 20 mm.

Please note that another model exists with dimensions 25 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

The clamp is suitable for hoses with diameters ranging from 12 mm to 18 mm and is used on some gliders for the water ballast system in the wing.

The clamp is suitable for hoses with diameters ranging from 12 mm to 20 mm. It is specifically used in the fuel system of the Arcus M and Arcus T.

This MPX-PIK male cable (cross-section 2.5 mm², length 30 cm) connects the most of the modern glider’s electrical system to a battery equipped with an MPX female connector.

This galvanized tension spring (type RZ-069) is used for the turbo compartment doors on the Arcus T, Duo Discus T, Discus-2T, Ventus-2cT, Ventus-2cxT and Ventus-3T Performance models.

It is used in the trim system of the Arcus, Duo Discus, Nimbus-4, and Nimbus-4D gliders, in the rear position, with two springs installed per glider.

This tension spring (ref RZ-124) is used in the rudder pedal of the Arcus, Duo Discus, and Nimbus-4D gliders, in the rear position, with two springs installed per glider. It is also used for the doors of the engine box in single seater.

This tension spring (ref. S-4640) is used in the turbo box of the Arcus T, Arcus T edition 2020, Duo Discus T, and Duo Discus xLT.

This bracket is designed for the battery holders installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The full box is available in the suggested products section at the bottom of the page.

This battery holders is installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The metalic bracket is available in the suggested products section at the bottom of the page.