Hardware
-
Nicopress-oval sleeve 1,5-2 mm
Nicopress-oval sleeve 1,5-2 mm, ref : NT281C-A or N° 28-1-C.
It is 10 x 6 x 4 mm.
from 1 € 0.21 incl. 19% VAT
€ 0.18 -
Washer Ø4,3xØ20x1,25 DIN 522 for the fin tank dump valve
This washer is used for the tail ballast dump valve of most of the Schempp-Hirth gliders.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Thimble 2,5 mm galvanized
Thimble 2,5 mm galvanized.
It is 27 x 15 x 5 mm.
from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Safety ring-spring steel, DIN471, size 12
This safety ring-spring steel, DIN471, size 12 is used to secure the tailwheel axle of, almost, all Schempp-Hirth gliders.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Screw for the seat pan
This oval countersunk head screw is used for the seat pan.
It is size M 5 x 16.
from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Self lock nut M6-8 and M8-8
Safety nut, DIN 985 galvanized
Availabe in thread size M6 or M8.
from 1 € 0.24 incl. 19% VAT
€ 0.20from 1 € 2.38 incl. 19% VAT
€ 2.00from 1 € 0.24 incl. 19% VAT
€ 0.20from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Washer M06 galvanized, DIN 125 / ISO 7090 Form B
Washer M06 galvanized, DIN 125 / ISO 7090 Form Bfrom 1 € 0.24 incl. 19% VAT
€ 0.20 -
washer 6,4, DIN 9021 / ISO 7093-1 galvanized
This washer is mainly used on the rear part of the horizontal tail fitting.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Self-locking hexagonal-head nut, M8, DIN 14441
This slotted hexagonal-head nut, M8, DIN 14441 is copper plated and is commonly used for rudder fixation.from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Cup washer for the seat pan
These cup washers are used for the bucket seat.
It is size M6 and its dimensions are 13 x 13 x 3 mm.
Tip: For a nicer finish, use these M6 washers with M5 screws (See suggested products).
from 1 € 0.26 incl. 19% VAT
€ 0.22 -
Hexagon Screw M06x18 - 8.8, DIN 933 / ISO 4017
This 6k-Screw is used for the elevator drive U-bracket.from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Roll pin for aileron
These roll pins are used to secure the aileron.
Dimension: 2 x 10 mm
DIN 1481 / ISO 8752
from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Roll pin for trim
Roll pin DIN 1481 / ISO 8752 stainless.
They are (mainly) used to in trim of the Arcus, Duo Discus XL and Nimbus-4DL.
There is two models : On gliders produced after April 2015, you will probably need the 2 x 16 mm model. For the older glider you will need to use the 2x14 mm roll pins. Please have a look in your glider to confirm which models you need.
from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Lock nut M6 TRELOC, DIN 439 galvanized
from 1 € 0.38 incl. 19% VAT
€ 0.32 -
DZUS S-washer
This washer is used with the DZUS-quick fastener pin. It is size 6, its diameter is 12 mm and it is made of plastic.
from 1 € 0.48 incl. 19% VAT
€ 0.40 -
Nicopress-Stop sleeve 1,5-1,7mm
Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).
It is 5 x 5 x 5 mm.from 1 € 0.48 incl. 19% VAT
€ 0.40 -
Schnorr-safety washer
Safety washers Form S available in M6 and M8.
These washers are used, among other things, to secure the rear part of the horizontal tail fitting and the elevator drive U-bracket.
from 1 € 0.48 incl. 19% VAT
€ 0.40 -
Safety ring-spring steel, DIN471, size 8
This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.from 1 € 0.55 incl. 19% VAT
€ 0.46 -
Nicopress-Stop sleeve 2,5 mm
Nicopress-Stop sleeve 2,5 mm, NTG282G-100.
It is 10 x 9 x 6 mm.
from 1 € 0.67 incl. 19% VAT
€ 0.56 -
Rubber washer 19x3 mm for the fin tank dump valve
This rubber washer ensures the sealing of the tail ballast of most of the Schempp-Hirth gliders.
It is advisable to replace it every 4-6 years to avoid water leaks.from 1 € 0.82 incl. 19% VAT
€ 0.69 -
Thimble 3,5 mm galvanized
Thimble 3,5 mm galvanized.
It is 32 x 17 x 6 mm.
from 1 € 0.94 incl. 19% VAT
€ 0.79
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.