-
Nicopress-Stop sleeve 1,5-1,7mm
Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).
It is 5 x 5 x 5 mm.from 1 € 0.48 incl. 19% VAT
€ 0.40 -
elevator-trim blade spring for Arcus, all Duo Discus, all Nimbus-4D and all Discus
This spring is used for the trim of the Arcus, Duo Discus XL, Nimbus-4DL and all the Discus from the Discus a to the Discus-2c.
It is 25mm lage and the legs are 40mm long. The central part is 12,5mm.
Some glider need roll pins. They are not included but they can be baught individaly (see the suggested products).
from 1 € 4.65 incl. 19% VAT
€ 3.91 -
Coolant temperature sensor for Solo 2625 01 and 02
This sensor is used in the Solo 2625 01 and 2625 02 to measure the water temperature.
The sensor used on the Arcus M and Ventus-3M (Solo 2625 01i and 02i) is different. You can find it on the suggested products.
from 1 € 147.80 incl. 19% VAT
€ 124.20 -
Brass bushing for the lower rudder framework fin of the Ventus a, b, and c and Discus a and b
This brass bushing is part of the lower framework of the rudder fin on Ventus a, b and c, and the Discus a and b.
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On more modern gliders the diameter of the head is 16 mm instead of 14 mm. You cannot use one for the other.
from 1 € 8.03 incl. 19% VAT
€ 6.75 -
Tesafix roll 9 and 12 mm
This double side tape (Tesafix 4965) is used for control surface sealing and is available in 2 different widths: 9 or 12 mm.
A roll contains 50 meters of tape.
from 1 € 20.15 incl. 19% VAT
€ 16.93from 1 € 20.74 incl. 19% VAT
€ 17.43from 1 € 28.02 incl. 19% VAT
€ 23.55 -
Shim washer kit for 18 mm wing bolt
These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.
They fit a 18 mm wing bolt. That includes the front and back bolts at the wing root of the double seaters.
These washers internal diameter is 17,8 mm. They are a bit smaller than the pin in order to stay in place when installed.
from 1 € 48.27 incl. 19% VAT
€ 40.56 -
Brake pads for Cleveland caliper 30-9
These brake lining (Tost p/n 075865) are used on brake assembly 30-9.
It can be mounted to 4′′, 5′′ and 6′′ disk brake wheels of the series Penta, Tria and Classic and on the original Cleveland brakes- wheel system.
Different system has been used and several TN have been approved. Please look carefully to your brakes and order similar brake pad.
from 1 € 72.08 incl. 19% VAT
€ 60.57 -
Main wheel axle castle nut, M12
This is the castle nut is used for the main landing gear of almost all Discus, Discus-2, Ventus-2 as well as the Ventus-3.
It is 8 mm, M12 x 1,5 DIN 937.
from 1 € 12.91 incl. 19% VAT
€ 10.85 -
Exhaust gasket for Solo 2625
Gasket exhaust is used for the SOLO engines 2625.
It is 68,5 x 48 x 2 mm.
It is sold by the unit.
from 1 € 25.87 incl. 19% VAT
€ 21.74
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.