-
Handle Fixation Kit to Canopy Frame
This kit is composed of:
- Shim washer 6 x 12 x 0.5; ref: B40-1479
- Brass bush 8 x 1 x 11.1; ref: B40-0438
- Polystop nut M6-8 DIN 985; ref: L01-0129
- Spring washer B8 DIN 137; ref: L01-0967
This kit contains all the hardware required for the fixation of the handle to the canopy frame.
Note: another set is required to fix the handle to the rode.
from 1 € 5.95 incl. 19% VAT
€ 5.00 -
Handle Fixation Kit to the canopy lock connecting rods
This set consists of:
- Brass bushing 8 x 1.5 x 6.2; Ref.: B40-1571
- Countersunk screw M5x16 - 8.8; ISO 10642 Ref.: L01-1012
- Polystop nut M5-8 DIN 985; Ref.: L01-0703
- Washer 5x10x0.5 mm DIN 988; Ref.: L01-0390
This set contains all the parts required to attach the handle to the connecting rod.
Note: An additional set is required to attach the handle to the canopy frame.from 1 € 5.95 incl. 19% VAT
€ 5.00 -
Bush for engine suspension for Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM
This bushing is Ø16x3x24,1.
It is used for the engine bearing of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM
from 1 € 5.96 incl. 19% VAT
€ 5.01 -
Turbulator tape 0,85x10 (per meter)
This turbulator band (or Noppenband) is 10 mm large. The dimples are 0,85 mm high and they are distanced by 10 mm.
This model is mainly used for the Ventus-3. Look at your sealing instructions for more information.
It is sold by the meter.
from 1 € 6.09 incl. 19% VAT
€ 5.12 -
Yellow T-handle, for tow-hook actuation
from 1 € 6.13 incl. 19% VAT
€ 5.15 -
Black T-handle
from 1 € 6.13 incl. 19% VAT
€ 5.15 -
Shim washer for 10 mm diameter wing bolt
These washers are 14x9,8x0,5 mm.
They are made for the wing bolt that have a 10 mm diameter. This includes the wing extension bolt of all Arcus, all Duo Discus, the Nimbus-3, -3D, -4 and -4D, the Janus, the Discus-b, the Discus-2a and -2b and the Ventus c. It is also the case for the winglet bolt of the Discus, the Standard Cirrus, the Ventus-2a and the Ventus-2b.
These washers internal diameter is 9,8 mm. They are a bit smaller than the pin in order to stay in place when installed.
They are sold in a kit of 4.
from 1 € 6.14 incl. 19% VAT
€ 5.16 -
Bowden cable 5,3x4,4x3,0 mm
This bowden cable is 5,3 x 4,4 x 3,0 mm. It can also be referred to as 5.51.0000.022.
It is sold by the meter and includes 2 cable end caps.
This cable is often used for the wheel brake systems. Please refer to your maintenance manual for the type of cable you need and how to make the connections.
from 1 € 6.27 incl. 19% VAT
€ 5.27 -
Clevis G4x16 DIN 71752
Stainless steel fork head (clevis) with a 4 mm pin diameter and a 16 mm fork width, manufactured in accordance with DIN 71752.
It is used in the fuel actuation system of the Duo Discus T, Duo Discus xT, Duo Discus xLT, Arcus T, Arcus 20 T, Arcus 20 M, and Ventus-3M Neo.
from 1 € 6.30 incl. 19% VAT
€ 5.29 -
Knurled nut M10 for trim weight
This knurled nut M10 DIN 467 is used to secure the cockpit weights of all the Ventus-3, the Arcus and some Duo Discus (xL).
It is sold with the safety pin (L01-0142)
from 1 € 6.31 incl. 19% VAT
€ 5.30 -
Landing gear guide plate for singel seater
This plate in grey PVC is used as a guide for all single-seater landing gear (except for the Ventus-3).
Its length is 220 x 24 mm and there is no hole. Adjust it to your glider.
from 1 € 6.47 incl. 19% VAT
€ 5.44 -
Gasket for the canopy of single-seaters
Gasket for the canopy frame of single-seat gliders, sold by the metre.
Please note: some gliders have this gasket on one side only, with a different seal on the other side (the one used for the two-seaters, see recommanded product). Please check your glider carefully before ordering.
from 1 € 6.49 incl. 19% VAT
€ 5.45 -
Spring-loaded pull button
This indexing plunger without lock is used for the adjustment mechanism of the headset position in all Arcus M models, and for the oxygen bottle mount in the Arcus Edition 2020 and Ventus-3.from 1 € 6.71 incl. 19% VAT
€ 5.64 -
Washer for spar bridge
This washer DIN 9021 M8, 8,4 bright countersunk is mainly use to fix the O2-bottle holder when the holder is over the spar bridge.
from 1 € 6.84 incl. 19% VAT
€ 5.75 -
Kit for the FES improved shunt screw connection (TN)
This kit contains:- 2 screws 3/8"- Length: 5/8"
- 2 lock washers
It is used to fulfil the TN 627-8, TN 863-26 and TN 825-59. Please read the TN carefully.from 1 € 7.14 incl. 19% VAT
€ 6.00 -
Brass bushing for lower rudder framework fin of the Discus-2, Ventus-2, Ventus-3 Sport, Duo Discus and some Arcus
This brass bushing is part of the lower framework of the rudder fin on Ventus-2, Discus-2, Ventus-3 sport, all Duo Discus and Arcus (except Arcus M).
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On older gliders the diameter of the head is 14mm instead of 16mm. See bellow the suggested products.
from 1 € 7.26 incl. 19% VAT
€ 6.10 -
Hexagon screw 08025, LN 9037
This 6k-Screw is mainly used at the rear part of the horizontal tail fitting.
from 1 € 7.27 incl. 19% VAT
€ 6.11 -
Tension spring for turbo engine doors, double seaters
This tension spring (ref. S-4640) is used in the turbo box of the Arcus T, Arcus T edition 2020, Duo Discus T, and Duo Discus xLT.from 1 € 7.41 incl. 19% VAT
€ 6.23 -
MPX-PIK cable, 30 cm
This MPX-PIK male cable (cross-section 2.5 mm², length 30 cm) connects the most of the modern glider’s electrical system to a battery equipped with an MPX female connector.from 1 € 7.52 incl. 19% VAT
€ 6.32 -
DZUS-quick fastener pin, Nextel painted
This quarter-turn lock is size 6, made in steel and with a left-hand thread.
This modell is Nextel painted, you can find the raw one bellow with the suggested products.
It is not adapted to all system. Please have a look and if your glider is equipped with the S-shaped system, order the reference L01-0045 via the spare part online form.
from 1 € 7.73 incl. 19% VAT
€ 6.50 -
Gasket exhaust 1,5mm, for SOLO 2350
SOLO Silent block bush, spare part n° 20 61 395
from 1 € 7.75 incl. 19% VAT
€ 6.51
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.