Spare parts

This label is made for the Arcus (Arcus M SN<216 and Arcus T SN<90).

 

These pictograms can be used in Discus-2 and Duo Discus.

This fiberglass bracket is designed for 7.5 Ah battery holders.

It has a width of 38 mm and fits a 97 mm battery. The shape is straight. 

A similar model (F60-0651) features a bend and is used in several gliders, including the Duo Discus XL and the Arcus. Please check the model installed in your glider carefully before purchasing.

This Polyflex brake hose fits the classic Duo Discus equipped with master cylinder model 7 and 30-9 brakes.

The hose length is 600 mm.

Depending on your glider configuration, you may also require two adapters, which can be found under recommended products (references: L07-1346 and L07-0406).

This 6PR tire from TOST AERO is used for all the 200x50 mm tailwheels and it is adapted to a large majority of modern Schempp-Hirth gliders.

This lid is used for the cooler of all the Ventus-3M (Solo 2625-01i and 2625-01i neo) and all the Arcus M (Solo 2625-02i) after 2018 but not for the other version. 

Please note that if the radiator of your glider is not black, you might need a different lid. Please contact Spare Parts.

This set of gasket can replace the on the main brake cylinder form 6 or 7. It is very likely that this type of cylinder is installed in the Duo Discus (but not in the x or xL), some Nimbus-4(D), as well as in some retrofitted Nimbus and Janus.

It do not work with the rectangular brake cylinder installed on some gliders (Ref: B40-1014). 

The temperature-indicator TF-00-059 is compact and readable. It temperatur captor can easily reach the front ventilation with its 125 cm cable.

This thermometer is mandatory for all the Schempp-Hirth gliders with water ballast.

This rubber boot surrounds the upper part of the elevator rope.

It is 70 mm long and 75 mm large and the diameters of the openings are 65 and 18 mm.

These hinges are used to fix the landing gear door of the Arcus, Nimbus-4 and Duo Discus.

The countersunk screws (fuselage side) and countersunk-head rivet and their washers (door side) can be ordered as an option.

This plate is used for the Duo Discus T, Duo Discus xT, Duo Discus xLT, the Arcus T and Arcus T edition 2020.

This gas strut is 500N and it is used for the engine mount of the Ventus T, Discus T, Ventus cM, the Nimbus-3T and the Nimbus-4T.

More modern single seaters are using the reference L03-0122, that is 600N. You can find it on the suggested product.

This skid is 121 x 35 x 28,5 mm and is used for Discus a, Discus b, Ventus b, Ventus c and all the Ventus-2.

Double face tape is already fixed on the skid to instal it easily.

This rubber element is part of the spindelsuspension of the Ventus-2cM, Ventus-3M, Nimbus-4M, -4DM and Arcus M.

It is 34 mm long.

Depending on the equipment available to you, it might be easier to buy the complete part (B40-13772). See suggested products.

These filters (1 filter Pierburg 4.00030.80.0 and 1 filter KL14 Mahle) are used for the fuel system of the Arcus M.

This tension spring is used to hold the flap handle in the correct position.

It was originally used on the Janus C, Nimbus-3D, and Nimbus-4D, and is located on the rear cockpit wall (back seat).

However, some gliders have been modified and now use a flat spring (Ref. B40-0297) mounted near the spar bridge.

This skid is 164 x 48 x 36 mm is used for the Discus-2a, -2b and 2-c.

Double face tape is already fixed on the skid to instal it easily.