Spare parts

This item is part of the horizontal tailplane fixation back system of all the modern Schempp-Hirth gliders. The kit provides all the necessary parts to change 1 pin.

This part is used for the notching of the flaps of the Ventus c.

It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.

This sealing lid is for the Arcus edition 2020.

It is equipped of a non-return valve.

This comprehensive kit ensures compatibility with all Duo Discus equipped with a master cylinder model 7 / brakes 30-9. It provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 4000 mm of 1,8 mm cable
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

This plexi cover is made for the Janus, the Ventus b and some Ventus-2. It is used in the TN 349-42 / 825-57.

Its diameter is 53,5 mm and the central hole is 5 mm. The locking device is 100mm long.

 

This part is used for the notching of the flaps of the Ventus-2b.

It is 135 mm long and the screw holes are spaced 50 and 69 mm apart respectively.

This tire (Tost p/n 064491) is used for the the 4" wheel of the single seater (before the Ventus-2c and the Discus-2b).

These filters (reference 6064-0A / 0 450 905 401 and E230204) are used for the fuel system of the Ventus-3M.

The kit contains the cable (diameter 3,2 mm), 2 nicopress-oval sleeves, 2 thimbles and some silicone tube. One side is already assembled.

It can be use for the Ventus-2cM, Ventus-3M, the Nimbus-4M and -4DM and the Arcus M.

Please refer to the maintenance manual for the installation.

These brake linings (Tost P/N 080949) are designed for the BZT2 brake assembly installed after 2017 with a thread M10x1. It is not compatible with the model with a thread NPT See drawing.

The BZT2 system is compatible with 5″ and 6″ disc brake wheels from the Penta and Classic series. It is commonly installed on the Ventus-3 and Arcus edition 2020 models.

Please note that different braking systems have been used over time, and several Technical Notices (TN) have been approved. Carefully inspect your brakes before ordering to ensure you select the correct brake pad.

This kit includes a wide selection of spacer washers for tail wheel axle, measuring 16 x 2 mm with widths ranging from 1.5 to 6 mm. It is particularly useful if you plan to switch from a classic tailwheel to a mini version. Compatible with most gliders, except for the Arcus M, Ventus-3M, and Cirrus.

This rubber element is use for the engine mount of the Arcus M, the Ventus-3M, Ventus-2cM, the Ventus-2cxM, the Nimbus-4M and the Nimbus-4DM.

Its old reference is VW 431407181D.

 

This air filter RC-1060 (Solo ref: 25 00 845) is used for the 2625-02i.

It used to be rectangular but the shape changed. You can use this model instead of the square ones.

This sensor is used in the Solo 2625 01 and 2625 02 to measure the water temperature.

The sensor used on the Arcus M and Ventus-3M (Solo 2625 01i and 02i) is different. You can find it on the suggested products.

This l'Hotellier ball end is used for gliders with manual control hookups.

For some gliders, including the Cirrus, you need a washer and a locknut. They are included in the package.

The EASA Form 1 is included when needed.

This bracket is designed for the battery holders installed on the rear side of the front pilot seat, close to the aft pilot’s leg area. 

The full box is available in the suggested products section at the bottom of the page.

This fuel tube is use for the Nimbus-4D T, the Duo Discus T, Duo Discus xL T and the Arcus T.

This proximity switch (ref  IX02 0815) is used for the automatic propeller brake in the Arcus M. 

It is not addapted to the Arcus M edition 2020.

This position sensor is sold as a unit (you might need two of them) and the FUT plug is included.