-
Bellow V6-269 for water ballast control rod
This rubber boot is surrounding the water ballast control rod to avoid the water leaking through. It is used in several Schempp-Hirth gliders including the Nimbus-2, Ventus, Ventus-2c, Discus-2c, Duo Discus and the Arcus.
It is 125 x 22 x 22 mm with a 7 mm and a 16 mm opening.
Over the years, other bellows and different combinations have been used. You can find them underneath this description, in the "suggested products", if you want to compare them with the model that you wish to replace.
from 1 € 21.74 incl. 19% VAT
€ 18.27 -
Flap latch-in element for Ventus-2b
This part is used for the notching of the flaps of the Ventus-2b.
It is 135 mm long and the screw holes are spaced 50 and 69 mm apart respectively.
from 1 € 109.37 incl. 19% VAT
€ 91.91 -
Flap latch-in element for Ventus c
This part is used for the notching of the flaps of the Ventus c.
It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.
from 1 € 105.15 incl. 19% VAT
€ 88.36 -
Brass bushing for lower rudder framework fin of the Discus-2, Ventus-2, Ventus-3 Sport, Duo Discus and some Arcus
This brass bushing is part of the lower framework of the rudder fin on Ventus-2, Discus-2, Ventus-3 sport, all Duo Discus and Arcus (except Arcus M).
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On older gliders the diameter of the head is 14mm instead of 16mm. See bellow the suggested products.
from 1 € 7.26 incl. 19% VAT
€ 6.10 -
Oxygen-bottle holder for gliders with engine
This oxygen bottle holder is suitable for a majority of gliders equiped with a turbo or a motor.
Please choose which holder you need according to your Oxygen-bottle diameter. It is possible to adjust the holder at +/- 2 mm.
In single-seaters, one of the screws of the support is often above the spar bridge, where the wall is relatively thin. It is therefore often necessary to add the washer B40-2218 (see suggested products).
from 1 € 228.86 incl. 19% VAT
€ 192.32 -
Teflon tape roll
The 30 mm large Teflon band is self adhesive.
A roll contains 10 meters of tape.
from 1 € 23.18 incl. 19% VAT
€ 19.48 -
Wing attachment bolt for double seaters, front
The visible part of the pin is 48 mm long and has a diameter of 18 mm. The inner part is 42 mm long and has a diameter of 40 mm.
It is used on the wing roots front part of the double seaters as well as for the front and rear roots of the Janus.
from 1 € 50.28 incl. 19% VAT
€ 42.25 -
Brake pads Beringer ZEA01
These pads are used for the Beringer brakes of the Ventus-2, Discus-2, Duo Discus XL and Arcus.
We advise you to replace the pads before the thickness of friction material reachs 1.5 mm. For more information, you can consult the maintenace manual from Beringer.
A package contains the two pads used for one wheel.
from 1 € 83.30 incl. 19% VAT
€ 70.00 -
Landing gear pneumatic tension spring for Duo Discus X
This spring is 210N and it is used in the landing gear on the Duo Discus x.
This pneumatic spring is also used for the Arcus and the Duo Discus xL which have a Beringer wheel. For these planes, the spring is associated with a specific extension. You can find the full spare-part here.
An assembly jig for the tension pneumatic spring can be added as an option. If you don't have one, we advise you to buy it.
from 1 € 97.48 incl. 19% VAT
€ 81.92
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.