-
Bellow V6-269 for water ballast control rod
This rubber boot is surrounding the water ballast control rod to avoid the water leaking through. It is used in several Schempp-Hirth gliders including the Nimbus-2, Ventus, Ventus-2c, Discus-2c, Duo Discus and the Arcus.
It is 125 x 22 x 22 mm with a 7 mm and a 16 mm opening.
Over the years, other bellows and different combinations have been used. You can find them underneath this description, in the "suggested products", if you want to compare them with the model that you wish to replace.
from 1 € 21.74 incl. 19% VAT
€ 18.27 -
Flap latch-in element for Ventus c
This part is used for the notching of the flaps of the Ventus c.
It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.
from 1 € 105.15 incl. 19% VAT
€ 88.36 -
Flap latch-in element for Ventus-2b
This part is used for the notching of the flaps of the Ventus-2b.
It is 135 mm long and the screw holes are spaced 50 and 69 mm apart respectively.
from 1 € 109.37 incl. 19% VAT
€ 91.91 -
Brass bushing for the lower rudder framework fin of the Ventus a, b, and c and Discus a and b
This brass bushing is part of the lower framework of the rudder fin on Ventus a, b and c, and the Discus a and b.
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On more modern gliders the diameter of the head is 16 mm instead of 14 mm. You cannot use one for the other.
from 1 € 8.03 incl. 19% VAT
€ 6.75 -
Tesafix roll 9 and 12 mm
This double side tape (Tesafix 4965) is used for control surface sealing and is available in 2 different widths: 9 or 12 mm.
A roll contains 50 meters of tape.
from 1 € 20.15 incl. 19% VAT
€ 16.93from 1 € 20.74 incl. 19% VAT
€ 17.43from 1 € 28.02 incl. 19% VAT
€ 23.55 -
Shim washer kit for 18 mm wing bolt
These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.
They fit a 18 mm wing bolt. That includes the front and back bolts at the wing root of the double seaters.
These washers internal diameter is 17,8 mm. They are a bit smaller than the pin in order to stay in place when installed.
from 1 € 48.27 incl. 19% VAT
€ 40.56 -
Brake pads for Cleveland caliper 30-9
These brake lining (Tost p/n 075865) are used on brake assembly 30-9.
It can be mounted to 4′′, 5′′ and 6′′ disk brake wheels of the series Penta, Tria and Classic and on the original Cleveland brakes- wheel system.
Different system has been used and several TN have been approved. Please look carefully to your brakes and order similar brake pad.
from 1 € 72.08 incl. 19% VAT
€ 60.57 -
Main wheel axle castle nut, M12
This is the castle nut is used for the main landing gear of almost all Discus, Discus-2, Ventus-2 as well as the Ventus-3.
It is 8 mm, M12 x 1,5 DIN 937.
from 1 € 12.91 incl. 19% VAT
€ 10.85 -
Exhaust gasket for Solo 2625
Gasket exhaust is used for the SOLO engines 2625.
It is 68,5 x 48 x 2 mm.
It is sold by the unit.
from 1 € 25.87 incl. 19% VAT
€ 21.74
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.