-
Brake pads Beringer ZEA01
These pads are used for the Beringer brakes of the Ventus-2, Discus-2, Duo Discus XL and Arcus.
We advise you to replace the pads before the thickness of friction material reachs 1.5 mm. For more information, you can consult the maintenace manual from Beringer.
A package contains the two pads used for one wheel.
from 1 € 83.30 incl. 19% VAT
€ 70.00 -
Elevator-bell crank
This item is part of the horizontal tailplane actuation system of all modern Schempp-Hirth gliders.
Please note that the Cirrus is equipped with a slightly different model. If you are unsure which model you need, please contact Schempp-Hirth Spare Part.
from 1 € 83.73 incl. 19% VAT
€ 70.36 -
Wingtip wheel, Lindner System, for Arcus
This wingtip wheel is made for the Arcus. The diameter of the rim is 90 mm and it is associated with a Ø80 x Ø10 O-Ring.
It is sold by the unit.
from 1 € 84.87 incl. 19% VAT
€ 71.32 -
Self sealing coupling for the Ventus-3M and Arcus M
This coupling is used for the fuel line going to the wing tank of the Ventus-3M and the Arcus M.
Please make sure you are entitled and have the skills to change that part. It should be secured with Loctite 577.
Please note: The coupling for the vent line is different.
from 1 € 85.17 incl. 19% VAT
€ 71.57 -
Wingtip skid for all Duo Discus
This skid is 194 x 47 x 37 mm and is used for all Duo Discus.
Double face tape is already fixed on the skid to make it easy to instal.
from 1 € 86.81 incl. 19% VAT
€ 72.95 -
Landing gear door spring for Arcus and Duo Discus XL
from 1 € 87.85 incl. 19% VAT
€ 73.82 -
Wingtip wheel, Lindner System, for Duo Discus, Discus-2c, Ventus-2c and Ventus-3
This wingtip wheel is 84 x 84 x 11 mm rim with a 60 x 10 O-Ring NBR70 tyre. It made for the Lindner system wingtip wheels of the Duo Discus, Discus-2c and the Ventus.
It is sold by the unit.
from 1 € 88.94 incl. 19% VAT
€ 74.74 -
Flap latch-in element for Ventus-2c, -2cx and -2bx
This part is used for the notching of the flaps of the Ventus-2bx, Ventus-2c and Ventus-2cx.
It is 146 mm long and the screw holes are spaced 50 and 69 mm apart respectively.
from 1 € 89.75 incl. 19% VAT
€ 75.42 -
BWS Pulley set
The deflection pulley is used to eliminate friction from the Bowden cables (in mosquito cleaner systems) in the event of major directional changes of the cable to enable lower manual force/power consumption and faster cleaning.from 1 € 90.44 incl. 19% VAT
€ 76.00 -
Turbulator tape roll
The classic Schempp-Hirth zigzag tape.
It is 12 mm large, and the zigzag are spaced by 6 mm.
A roll contains 15 meters of tape.
from 1 € 92.11 incl. 19% VAT
€ 77.40 -
Front canopy hinge for Arcus, Duo Discus xL and Nimbus-4DL
This hinge is for the canopy of all Arcus, Duo Discus xL and Nimbus-4DL.
This front hinge is printed in 3D and will break in case of evacuation. If it happens accidentally, it is possible to replace it. This hinge was previously in carbon fiber but you can replace it by that one with minor adjustments.
Note: the hinge at the back is different.
from 1 € 92.32 incl. 19% VAT
€ 77.58 -
Wing attachment bolt for Ventus-2c and Discus-2c, back
The visible part of the peg is 70,5 mm long with a 14 mm diameter. The internal part is 35 mm long, with a 40 mm diameter.
It is used on the back part of the Discus-2c and Ventus-2c wing roots.
from 1 € 93.58 incl. 19% VAT
€ 78.64 -
Wedekind safety device KIT
Kit to secure l'hotellier connector for gliders with manual control hookups.
It cannot be used for the wing extension.
It is sold by the unit and the EASA Form 1 is included.
from 1 € 95.66 incl. 19% VAT
€ 80.39 -
Landing gear pneumatic tension spring for Duo Discus X
This spring is 210N and it is used in the landing gear on the Duo Discus x.
This pneumatic spring is also used for the Arcus and the Duo Discus xL which have a Beringer wheel. For these planes, the spring is associated with a specific extension. You can find the full spare-part here.
An assembly jig for the tension pneumatic spring can be added as an option. If you don't have one, we advise you to buy it.
from 1 € 97.48 incl. 19% VAT
€ 81.92 -
Horiz. Tailplane Pin, Kit.
This item is part of the horizontal tailplane fixation back system of all the modern Schempp-Hirth gliders. The kit provides all the necessary parts to change 1 pin.
from 1 € 98.19 incl. 19% VAT
€ 82.51 -
Flap latch-in element for Ventus c
This part is used for the notching of the flaps of the Ventus c.
It is 135 mm long and the screw holes are spaced 50 and 68 mm apart respectively. The space between the first and the last step is 90 mm. Please look carefully at the drawing to make sure that it is really the part you need.
from 1 € 105.15 incl. 19% VAT
€ 88.36 -
Water filler cap for Arcus Edition 2020
This sealing lid is for the Arcus edition 2020.
It is equipped of a non-return valve.
from 1 € 106.60 incl. 19% VAT
€ 89.58 -
Kit for brake pull cable for the Duo Discus front seat
This comprehensive kit ensures compatibility with all Duo Discus equipped with a master cylinder model 7 / brakes 30-9. It provides the necessary components for a smooth brake cable replacement.
The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.
The kit includes:
- 4000 mm of 1,8 mm cable
- 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
- 1 x 2 mm thimble
- 1 x Nipple No. 33A
- 1 x Nipple support No. 21A (8 x 9 mm)
from 1 € 107.21 incl. 19% VAT
€ 90.09 -
Perspex disc 53,5 mm with bracket
This plexi cover is made for the Janus, the Ventus b and some Ventus-2. It is used in the TN 349-42 / 825-57.
Its diameter is 53,5 mm and the central hole is 5 mm. The locking device is 100mm long.
from 1 € 108.15 incl. 19% VAT
€ 90.88 -
Flap latch-in element for Ventus-2b
This part is used for the notching of the flaps of the Ventus-2b.
It is 135 mm long and the screw holes are spaced 50 and 69 mm apart respectively.
from 1 € 109.37 incl. 19% VAT
€ 91.91 -
Tyre 4.00-4 Tost AERO 8 pr
This tire (Tost p/n 064491) is used for the the 4" wheel of the single seater (before the Ventus-2c and the Discus-2b).
from 1 € 112.10 incl. 19% VAT
€ 94.20 -
Fuel filters for Ventus-3M
These filters (reference 6064-0A / 0 450 905 401 and E230204) are used for the fuel system of the Ventus-3M.from 1 € 114.49 incl. 19% VAT
€ 96.21 -
Kit pylon arresting wire for Ventus- 2cM, Ventus-3M, Arcus M, Nimbus-4M and -4DM
The kit contains the cable (diameter 3,2 mm), 2 nicopress-oval sleeves, 2 thimbles and some silicone tube. One side is already assembled.
It can be use for the Ventus-2cM, Ventus-3M, the Nimbus-4M and -4DM and the Arcus M.
Please refer to the maintenance manual for the installation.
from 1 € 114.66 incl. 19% VAT
€ 96.35 -
Brake pad for Tost BZT2 (Post-2017 Models)
These brake linings (Tost P/N 080949) are designed for the BZT2 brake assembly installed after 2017 with a thread M10x1. It is not compatible with the model with a thread NPT See drawing.
The BZT2 system is compatible with 5″ and 6″ disc brake wheels from the Penta and Classic series. It is commonly installed on the Ventus-3 and Arcus edition 2020 models.
Please note that different braking systems have been used over time, and several Technical Notices (TN) have been approved. Carefully inspect your brakes before ordering to ensure you select the correct brake pad.
from 1 € 116.86 incl. 19% VAT
€ 98.20 -
Tail wheel axle distance washer kit
This kit includes a wide selection of spacer washers for tail wheel axle, measuring 16 x 2 mm with widths ranging from 1.5 to 6 mm. It is particularly useful if you plan to switch from a classic tailwheel to a mini version. Compatible with most gliders, except for the Arcus M, Ventus-3M, and Cirrus.from 1 € 121.43 incl. 19% VAT
€ 102.04 -
Canopy locking mechanism for Duo Discus and Nimbus-4D
This kit is for the TN 380-1 and TN396-6.
According to your glider, you might need the optional guide or not.
Please read the TNs carefully.
from 1 € 126.14 incl. 19% VAT
€ 106.00from 1 € 332.95 incl. 19% VAT
€ 279.79 -
Rubber element for the almost all modern engine mounts
This rubber element is use for the engine mount of the Arcus M, the Ventus-3M, Ventus-2cM, the Ventus-2cxM, the Nimbus-4M and the Nimbus-4DM.
Its old reference is VW 431407181D.
from 1 € 142.13 incl. 19% VAT
€ 119.44 -
Air filter for SOLO 2625-02i
This air filter RC-1060 (Solo ref: 25 00 845) is used for the 2625-02i.
It used to be rectangular but the shape changed. You can use this model instead of the square ones.
from 1 € 142.86 incl. 19% VAT
€ 120.05 -
Coolant temperature sensor for Solo 2625 01 and 02
This sensor is used in the Solo 2625 01 and 2625 02 to measure the water temperature.
The sensor used on the Arcus M and Ventus-3M (Solo 2625 01i and 02i) is different. You can find it on the suggested products.
from 1 € 147.80 incl. 19% VAT
€ 124.20 -
Rotule L'Hotellier MS 961-150-150-L3
This l'Hotellier ball end is used for gliders with manual control hookups.
For some gliders, including the Cirrus, you need a washer and a locknut. They are included in the package.
The EASA Form 1 is included when needed.
from 1 € 156.34 incl. 19% VAT
€ 131.38 -
Bracket for battery box for double seaters
This bracket is designed for the battery holders installed on the rear side of the front pilot seat, close to the aft pilot’s leg area.
The full box is available in the suggested products section at the bottom of the page.
from 1 € 157.65 incl. 19% VAT
€ 132.48 -
Tube 5.00-5 (and 6.00), TR87
This tube fits 5.00 and 6.00 tyres.
Its short valve is adapted for almost all single seater with a 5" wheel (except the one equipped with TOST drum brakes like the Kobold 5"). It is also used for the double seaters equipped with a TOST Penta wheel.
You can find the tube 5.00-5, TR67, with a long valve, in the suggested products.
from 1 € 159.34 incl. 19% VAT
€ 133.90 -
Fuel tube for double seater with turbo
This fuel tube is use for the Nimbus-4D T, the Duo Discus T, Duo Discus xL T and the Arcus T.from 1 € 162.95 incl. 19% VAT
€ 136.93 -
Limit switch IX02 0815
This proximity switch (ref IX02 0815) is used for the automatic propeller brake in the Arcus M.
It is not addapted to the Arcus M edition 2020.
This position sensor is sold as a unit (you might need two of them) and the FUT plug is included.
from 1 € 163.33 incl. 19% VAT
€ 137.25 -
Rear Headrest Racket
This support is used on a fuselage side, to fixe the rear headrest.
It is composed of the headrest holder, the locking plate, the 7.2mm bolt and the part that connect to the fuselage.
from 1 € 164.22 incl. 19% VAT
€ 138.00 -
Elevator transition for all Discus-2, select Ventus-2, and the Ventus-3
This part can be adapted to fit the Discus-2a, Discus-2b, Discus-2c, Ventus-2ax, Ventus-2bx, the ventus-2c, the ventus-2cx and the Ventus-3.
It measures 148 mm in width.
Please note that you will need to cut the part to ensure it fits your glider, as it is sold in an untrimmed form.
from 1 € 172.92 incl. 19% VAT
€ 145.31 -
Elevator transition for Duo Discus, Arcus and Nimbus-4D
This part can be adapted to fit the Duo Discus, Duo Discus X, Duo Discus XL, as well as the Arcus, Arcus Edition 2020, and Nimbus-4D.
It measures approximately 147 mm in width and 157 mm in length.
Please note that the part is sold in an untrimmed form, so you will need to cut it to ensure a proper fit for your glider.
from 1 € 172.92 incl. 19% VAT
€ 145.31 -
Pneumatic tension spring connecting the flap to the airbrake
This 200N gas strut is in the airbrake box. It connects the airbrake rod to the actuating lever of the trailing edge flap for the Duo Discus X and xL as well as the Nimbus-3D, -4 and -4D.
An older version used a gas spring from the company Hahn, you can use this one instead.
from 1 € 175.92 incl. 19% VAT
€ 147.83 -
Rubber element of the spindle suspension for almost all M
This part is used for the Discus bM, the Ventus-2cM, the Ventus-3M, the Nimbus-4DM and the Arcus M.from 1 € 177.57 incl. 19% VAT
€ 149.22 -
Oxygen-bottle holder for pure gliders
Thees oxygen bottle holders are suitable for a majority of pure Schempp-Hirth gliders.
Please choose which holder you need according to the diameter of your Oxygen-bottle. It is possible to adjust the holder at +/- 2mm.
In single-seaters, one of the screws of the holder is often above the spar bridge, where the wall is relatively thin. It is therefore often necessary to add the washer B40-2218 (see suggested products).
from 1 € 177.63 incl. 19% VAT
€ 149.27 -
Landing gear pneumatic tension spring for Duo Discus XL and Arcus with Beringer wheel
This gas strut is 210N and it is used in the landing gear on the Arcus and Duo Discus xL.
This model is made for Beringer wheels. If you have a TOST wheel, we advise you to use this model.
You can order the pneumatic spring alone, without the pivot ball nor the extension here.
An assembly jig for the tension pneumatic spring can be added as an option. If you don't have one, we advise you to buy it.
from 1 € 178.73 incl. 19% VAT
€ 150.19 -
Pneumatic tension spring for mini Nimbus airbrakes
This 150N gas strut is used for the Mini-Nimbus airbreaks.
from 1 € 182.71 incl. 19% VAT
€ 153.54 -
Polyflex-hose for Ventus-2 and Discus-2 using the disc brakes type Magura (Option)
This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.
Polyflex-hose is 1004 CK and it is 1080mm.
from 1 € 186.57 incl. 19% VAT
€ 156.78 -
New suspension for the powerplant spindle drive on Arcus M
Optional Spindle Drive Modification for Maintenance & Production according to TN A532-12
Our spindle drive system, responsible for extending and retracting the power plant, is designed with rubber-mounted suspension for optimal vibration isolation. This optional modification increases reliability.
Within the scope of maintenance and manufacture, it is also permissible to replace only the front, fuselage-side suspension (Action 1) or only the rubber mount of the rear, propeller arm-side suspension (Action 2).
- Kit 1: Front Suspension: Integrated within the fuselage
- Kit 2: Rear Suspension: Mounted on the propeller arm
from 1 € 188.29 incl. 19% VAT
€ 158.23from 1 € 336.00 incl. 19% VAT
€ 282.35from 1 € 242.15 incl. 19% VAT
€ 203.49from 1 € 578.15 incl. 19% VAT
€ 485.84 -
Tyre 2.80/2.50-4 for double seater nose wheel
This 2.80/2.50-4 tire is used for the front wheel of the Janus, Duo Discus, and Arcus.
Previously, a 3" tire (D 3.00-4 IND IC35 4PR) was used, but that model has been discontinued. This tire serves as a suitable replacement.
from 1 € 190.40 incl. 19% VAT
€ 160.00 -
Landing gear pneumatic tension spring for Duo Discus XL und Arcus with a TOST wheel
This gaz strut is 210N and it is used for the landing gear on the Arcus and Duo Discus XL.
Important: It is not adapted for Beringer wheels.
Two models exist. The pivot ball was first associated with a M5 screw, before beeing replace by a M6 screw in 2015. Please measure the diameter of the screw on the part that you are currently using, and order the same.
An assembly jig for the tension pneumatic spring can be added as an option. If you don't have one, we advise you to buy it.
from 1 € 193.02 incl. 19% VAT
€ 162.20from 1 € 193.02 incl. 19% VAT
€ 162.20from 1 € 189.33 incl. 19% VAT
€ 159.10 -
Coolant hoses set for SOLO 2625 02
This hose set is designed for use with the Solo 2625 02 and 02i engines in the Arcus M and Arcus M edition 2020 gliders.from 1 € 201.01 incl. 19% VAT
€ 168.92 -
Ignition coil for Solo 2625 type "i" from PVL
The ignition box from PVL is used for the Solo 2625-01i and 2625-02i but not for the other version. The Solo 2625-01 and 2625-02 need the ignition coil from Ducati.from 1 € 207.30 incl. 19% VAT
€ 174.20 -
Fin tank valve for all single seaters (exc. Ventus-3)
This is the complete tank dump valve assembly. It is used for all single seaters except for the Ventus-3.
Arcus and Duo Discus xL have other model. See suggested products below. For first generation Duo Discus, Janus, Nimbus-3D and -4D, please contact our sparepart team.
from 1 € 213.13 incl. 19% VAT
€ 179.10 -
GFRP-cover for Ventus-3M starter ring gear, TN 627-5
This GFRP-cover (G000168) is used for the TN 627-5.
That is recommanded for the Ventus-3M (SN < 183).
Please read carefully the Technnical Note.
from 1 € 213.43 incl. 19% VAT
€ 179.35 -
Horizontal tailplane fitting, snap lock
This item is part of the stabilizer fixation of all the modern Schempp-Hirth gliders.
It is possible to replace or change it for a bigger pin diameter to compensate the ageing of the parts on the stabilizer.
This item is delivered with 4 allen screw M06x30 - 8.8, DIN 912 / ISO 4762 galvanized (L01-0119) and 4 Schnorr-safety washer M6 (L01-0378).
from 1 € 214.01 incl. 19% VAT
€ 179.84from 1 € 214.01 incl. 19% VAT
€ 179.84from 1 € 214.01 incl. 19% VAT
€ 179.84from 1 € 214.01 incl. 19% VAT
€ 179.84
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.