Controls

Nicopress-Stop sleeve 3,0-3,5 mm, NT283M / n° 28-3-M.

It is 14 x 12 x 8 mm.

This is a galvanized, spring-loaded, self-locking hex nut in M10 size, manufactured to the SSB 003 specification with an FK4 flat design and a 17 mm wrench size.

It is used on the landing gear of nearly all Schempp-Hirth gliders, for the shock absorber and/or the drag strut.

This screw is used for the Ventus-2c with a 5" Classic wheels from TOST and a Magura cylinder brake.

It is 25 mm long and the head size is 14 mm.

This 6k-screw is used for the elevator drive U-bracket.
 

The clamp is suitable for hoses with diameters ranging from 6 mm to 7 mm and is used on some gliders for the rudder pedal cable.

This tension spring (ref RZ-124) is used in the rudder pedal of the Arcus, Duo Discus, and Nimbus-4D gliders, in the rear position, with two springs installed per glider. It is also used for the doors of the engine box in single seater.

Tension Spring for the Discus-2 Trim System, Part No.: RZ-123 I

Tension spring for the trim system of the Discus-2 series. 3 springs are required per aircraft.

It is  Ø 1,6 x 14,1 x 59 mm

 

This high-quality, flexible shrink tubing is used for insulation and protection of cables and connections – including many fuel lines and some electronic components.

Minimum diameter before shrinking: 12.7 mm

Diameter after shrinking: 6.4 mm

It is sold by the meter.

This pushrod guide ball cage measures 25 × 3 × 20 mm.

Please note that another model exists with dimensions 29 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This screw is mainly used to secure the rear part of the horizontal tail fitting.

This pushrod guide ball cage measures 29 × 3 × 20 mm.

Please note that another model exists with dimensions 25 × 3 × 20 mm.
Depending on the glider, you may need one, the other, or both types

 

This connection fitting is used, sometime, to the Polyflex hose of the classic Duo Discus which are using the Classic wheel from TOST with a Magura cylinder brake.

This spring is used for the trim of the Arcus, Duo Discus XL, Nimbus-4DL and all the Discus from the Discus a to the Discus-2c.

It is 25mm lage and the legs are 40mm long. The central part is 12,5mm.

Some glider need roll pins. They are not included but they can be baught individaly (see the suggested products). 

This bowden cable is 5,3 x 4,4 x 3,0 mm. It can also be referred to as 5.51.0000.022.

It is 80 cm and includes 2 cable end caps. To order a bigger quantity see the 

This cable is often used for the wheel brake systems. Please refer to your maintenance manual for the type of cable you need and how to make the connections.

 

These springs are used for the water dump system on the Mini-Nimbus, Duo Discus, Ventus-2c and Ventus 3.

It is 99,5 mm long and the diameter of the coiled is 15 mm. The steel wire diameter is 1,5 mm.

This bowden cable is 5,3 x 4,4 x 3,0 mm. It can also be referred to as 5.51.0000.022.

It is sold by the meter and includes 2 cable end caps.

This cable is often used for the wheel brake systems. Please refer to your maintenance manual for the type of cable you need and how to make the connections.

This plate in grey PVC is used as a guide for all single-seater landing gear (except for the Ventus-3).

Its length is 220 x 24 mm and there is no hole. Adjust it to your glider.

This 6k-Screw is mainly used at the rear part of the horizontal tail fitting.
 

This connection fitting (Tost p/n 075830) is in aluminium, with standard screwing JIC04 .

This system is used for the Ventus-2c, Discus-2b and Duo Discus which are using the 5" Classic wheel from TOST with a Magura cylinder brake.

This sealing is made for the Ventus-3 sealing caps.

Its diameter is 26 mm and the sealing is 4,0mm thick.