Controls

This 300N gas strut is located in the fuselage. It connects to the airbrake drive shaft in the Duo Discus x and xL.

If the airbrakes become very hard to operate, it may be that this gas strut needs to be replaced.

This sealing cap is made for the Ventus-3 outer wing.

The plug used for the inner wing is different. You can find it below in the suggested items.

Please note that the first seven Ventus-3 are equipped with a different system.

This Polyflex brake hose fits the classic Duo Discus equipped with master cylinder model 7 and 30-9 brakes.

The hose length is 600 mm.

Depending on your glider configuration, you may also require two adapters, which can be found under recommended products (references: L07-1346 and L07-0406).

This set of gasket can replace the on the main brake cylinder form 6 or 7. It is very likely that this type of cylinder is installed in the Duo Discus (but not in the x or xL), some Nimbus-4(D), as well as in some retrofitted Nimbus and Janus.

It do not work with the rectangular brake cylinder installed on some gliders (Ref: B40-1014). 

This rubber boot surrounds the upper part of the elevator rope.

It is 70 mm long and 75 mm large and the diameters of the openings are 65 and 18 mm.

This tension spring is used to hold the flap handle in the correct position.

It was originally used on the Janus C, Nimbus-3D, and Nimbus-4D, and is located on the rear cockpit wall (back seat).

However, some gliders have been modified and now use a flat spring (Ref. B40-0297) mounted near the spar bridge.

This cable is designed for the front seat of the Arcus, Duo Discus x, and Duo Discus xL equipped with a TOST wheel and a Magura cylinder brake.

The brake cable is 600 mm long, with a diameter of Ø1.5 mm, and is fitted with a 9 mm diameter nipple. The black segmented cable housing is included.

Please note, this cable is not compatible with the first-generation Duo Discus or the Arcus edition 2020, which are equipped, respectively, with master cylinder model 7 / brakes 30-9 and the BZT2 TOST brake system.

The EASA Form one is included.

This cable is designed for the front seat of the Arcus, Duo Discus x, and Duo Discus xL equipped with a TOST wheel and a Magura cylinder brake.

The brake cable is 600 mm long, with a diameter of Ø1.5 mm, and is fitted with a 9 mm diameter nipple.

Please note, this cable is not compatible with the first-generation Duo Discus or the Arcus edition 2020, which are equipped, respectively, with master cylinder model 7 / brakes 30-9 and the BZT2 TOST brake system.

The EASA Form one is included.

This kit contains all  you need to replace the pedal adjustment mechanism, including the instructions.

It is made for the Ventus b, Ventus c, Ventus-2, Discus, Discus-2, Nimbus-4, Duo Discus and the Arcus. 

On the Nimbus-4, the Ventus, the Discus and the Duo Discus the mecanisme included a spring. It is now replace by a gummi band. With this kit, you can upgrade the old sytem to the newest one.

This pilot stick handle is made by Air Ergo Leki for the Schempp-Hirth 19,3 mm diameter control sticks.

3 adaptors are provided for the  folowing settings: No SC, SC switch or SC button.

This is the handle for the trim of the Arcus, Duo Discus XL and Nimbus-4DL.

The roll pins are included. 

Please note the pin roll can be bought separatly (see suggested product). If your glider is older than April 2015, you need to use the 2x14 mm roll pins instead of 2x16 mm.

 

This item is used to fix the elevator bell crank to the fuselage on almost all Schempp-Hirth gliders.

Screws and washers are provided.

This comprehensive kit ensures compatibility with all single-seater gliders equipped with drum brakes and provides the necessary components for a smooth brake cable replacement.

The cable comes with a standard 5.5 mm nipple, which fits most modern gliders that have a 6.2 mm handle hole. For older models or those with larger handle holes, an additional nipple is included, suitable for handles with an 8.5 mm hole.

The kit includes:

• 1600 mm of 2 mm cable with a 5.5 x 10 mm nipple
• 1 x Nicopress oval sleeve (1.5-2 mm, NT281C-A)
• 1 x 2 mm thimble
• 1 x Nipple No. 33A
• 1 x Nipple support No. 21A (8 x 9 mm)

These brake lining (Tost p/n 075865) are used on brake assembly 30-9.

It can be mounted to 4′′, 5′′ and 6′′ disk brake wheels of the series Penta, Tria and Classic and on the original Cleveland brakes- wheel system.

Different system has been used and several TN have been approved. Please look carefully to your brakes and order similar brake pad.