-
Eta fuse for instuments
These fuses are used for instruments.
They are available in 2, 4 and 6,3 A.
from 1 € 13.09 incl. 19% VAT
€ 11.00from 1 € 20.40 incl. 19% VAT
€ 17.14from 1 € 11.33 incl. 19% VAT
€ 9.52 -
Tailwheel tube 200x50 with 90° valve
This tube is for all 200x50 mm tailwheels and it is adapted to a large majority of modern Schempp-Hirth gliders.
from 1 € 10.60 incl. 19% VAT
€ 8.91 -
Landing gear guide plate for singel seater
This plate in grey PVC is used as a guide for all single-seater landing gear (except for the Ventus-3).
Its length is 220 x 24 mm and there is no hole. Adjust it to your glider.
from 1 € 6.47 incl. 19% VAT
€ 5.44 -
Oxygen-bottle neck-holder
This oxygen bottle support is suitable for a majority of Schempp-Hirth gliders.
Please choose the diameter of your oxygen bottle. If your bottle has a diameter that is not in the list, please contact Schempp-Hirth spare part.
Please note that for some bottle (like the "Montain High"), you will need an extender to shift the pressure gauge away from the bottle neck.
from 1 € 214.20 incl. 19% VAT
€ 180.00from 1 € 214.20 incl. 19% VAT
€ 180.00 -
Turbulator tape 0,8x5 for almost all gliders (Roll)
This turbulator band (or Noppenband) is 10 mm large and self-adhesive . The dimples are 0,8 mm high and they are distanced by 5 mm.
It is very often used on Schempp-Hirth glider but look at your sealing instructions as some gliders, like the Arcus and the Ventus 3, are using a different turbulator tapes.
The roll is 10 metres long.
from 1 € 35.99 incl. 19% VAT
€ 30.24 -
Airbrake drive funnel
This drive funnel is used on almost all Schempp-Hirth gliders except the Nimbus-4 and the Ventus-3.
Two lock nuts M 6-8, DIN 985 and a lock nut M6 TRELOC, DIN 439 are included. However, your glider has a specific set of distance washer that are not provided. Please before disassemble the funnel make sure you know which washer go where.
On the Ventus-2 and Discus-2c, you may also need a set of screws that can be baught as an option.
from 1 € 370.99 incl. 19% VAT
€ 311.76 -
Main brake cylinder for Ventus-2 and Discus-2 using the disc brakes type Magura (Option)
This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.from 1 € 375.87 incl. 19% VAT
€ 315.86 -
Main wheel axle
This is the axle for the main landing gear of almost all Discus, Discus-2, Ventus-2 and Ventus-3.
It is 215 mm long, including a M12x1,5 head (4 mm long) and a M12 screw thread (12 mm long).
Careful: some Ventus c, Ventus-2a, Ventus-2b and Discus-2b with carbon fiber undercarriage need another axle . If you are not sure, measure the axle that is currently used or contact Schempp-Hirth spare part.
You may also want to buy the 8 mm M12x1,5 castle nut which is used to secured the axle (See suggested products).
from 1 € 70.50 incl. 19% VAT
€ 59.24 -
Ignition coil for Solo 2625 type "i" from PVL
The ignition box from PVL is used for the Solo 2625-01i and 2625-02i but not for the other version. The Solo 2625-01 and 2625-02 need the ignition coil from Ducati.from 1 € 207.30 incl. 19% VAT
€ 174.20 -
Nicopress-Stop sleeve 1,5-1,7mm
Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).
It is 5 x 5 x 5 mm.from 1 € 0.48 incl. 19% VAT
€ 0.40 -
elevator-trim blade spring for Arcus, all Duo Discus, all Nimbus-4D and all Discus
This spring is used for the trim of the Arcus, Duo Discus XL, Nimbus-4DL and all the Discus from the Discus a to the Discus-2c.
It is 25mm lage and the legs are 40mm long. The central part is 12,5mm.
Some glider need roll pins. They are not included but they can be baught individaly (see the suggested products).
from 1 € 4.65 incl. 19% VAT
€ 3.91 -
Coolant temperature sensor for Solo 2625 01 and 02
This sensor is used in the Solo 2625 01 and 2625 02 to measure the water temperature.
The sensor used on the Arcus M and Ventus-3M (Solo 2625 01i and 02i) is different. You can find it on the suggested products.
from 1 € 147.80 incl. 19% VAT
€ 124.20 -
Brass bushing for the lower rudder framework fin of the Ventus a, b, and c and Discus a and b
This brass bushing is part of the lower framework of the rudder fin on Ventus a, b and c, and the Discus a and b.
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On more modern gliders the diameter of the head is 16 mm instead of 14 mm. You cannot use one for the other.
from 1 € 8.03 incl. 19% VAT
€ 6.75 -
Tesafix roll 9 and 12 mm
This double side tape (Tesafix 4965) is used for control surface sealing and is available in 2 different widths: 9 or 12 mm.
A roll contains 50 meters of tape.
from 1 € 20.15 incl. 19% VAT
€ 16.93from 1 € 20.74 incl. 19% VAT
€ 17.43from 1 € 28.02 incl. 19% VAT
€ 23.55 -
Shim washer kit for 18 mm wing bolt
These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.
They fit a 18 mm wing bolt. That includes the front and back bolts at the wing root of the double seaters.
These washers internal diameter is 17,8 mm. They are a bit smaller than the pin in order to stay in place when installed.
from 1 € 48.27 incl. 19% VAT
€ 40.56 -
Brake pads for Cleveland caliper 30-9
These brake lining (Tost p/n 075865) are used on brake assembly 30-9.
It can be mounted to 4′′, 5′′ and 6′′ disk brake wheels of the series Penta, Tria and Classic and on the original Cleveland brakes- wheel system.
Different system has been used and several TN have been approved. Please look carefully to your brakes and order similar brake pad.
from 1 € 72.08 incl. 19% VAT
€ 60.57 -
Main wheel axle castle nut, M12
This is the castle nut is used for the main landing gear of almost all Discus, Discus-2, Ventus-2 as well as the Ventus-3.
It is 8 mm, M12 x 1,5 DIN 937.
from 1 € 12.91 incl. 19% VAT
€ 10.85 -
Exhaust gasket for Solo 2625
Gasket exhaust is used for the SOLO engines 2625.
It is 68,5 x 48 x 2 mm.
It is sold by the unit.
from 1 € 25.87 incl. 19% VAT
€ 21.74 -
Nicopress-Stop sleeve 2,5 mm
Nicopress-Stop sleeve 2,5 mm, NTG282G-100.
It is 10 x 9 x 6 mm.
from 1 € 0.67 incl. 19% VAT
€ 0.56 -
Safety ring-spring steel, DIN471, size 8
This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.from 1 € 0.55 incl. 19% VAT
€ 0.46 -
Roll pin for trim
Roll pin DIN 1481 / ISO 8752 stainless.
They are (mainly) used to in trim of the Arcus, Duo Discus XL and Nimbus-4DL.
There is two models : On gliders produced after April 2015, you will probably need the 2 x 16 mm model. For the older glider you will need to use the 2x14 mm roll pins. Please have a look in your glider to confirm which models you need.
from 1 € 0.36 incl. 19% VAT
€ 0.30
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.