-
Control cable A 1,6 mm
Control cable A, 1.6 mm, ISO 2020 (1/16”), DIN 3051 compliant, 7x7 construction
Sold by the meter.
This cable is often used for the turbo engine decompression system and fin tank control. Please refer to your maintenance manual to determine the correct cable type and connection instructions.
It is also commonly used for rudder pedal adjustment. For this application, we recommend purchasing the "Kit for rudder pedal adjustment ".
from 1 € 4.49 incl. 19% VAT
€ 3.77 -
Mylar convex 0,19 mm, 22, 25 and 30 mm, Roll
This Mylarband, also named Hostaphanband or Profilband, is pre-curved and used for control surface sealing.
It is available in 3 different widths: 22, 25 and 30 mm. They are often refered as "Profilband 22mm / 0.19 mm strongly vaulted (vorgewölbt)", "Profilband 25 mm / 0.19 mm gewölbt" and "Profilband 30mm / 0.19 mm stark vorgewölbt".
A roll contains 15 meters of tape.
Note, 3 other models exist: plain, asymmetric curved and asymetric curved scarfed. Please refer to your glider control sealing instructions for more information.
from 1 € 68.37 incl. 19% VAT
€ 57.45from 1 € 54.62 incl. 19% VAT
€ 45.90from 1 € 51.76 incl. 19% VAT
€ 43.50from 1 € 74.79 incl. 19% VAT
€ 62.85 -
Gasket for canopy frame of the Double Seaters
This gasket is used for the canopy of the Duo Discus and the Arcus.
It is sold by the meter.
from 1 € 10.60 incl. 19% VAT
€ 8.91 -
KIT for fuel hose replacement at the 5-year inspection for Arcus M
This kit contains all the fuel hoses that need to be replaced during the 5 years inspection on the Arcus M.from 1 € 503.85 incl. 19% VAT
€ 423.40 -
Brass bushing for lower rudder framework fin of the Discus-2, Ventus-2, Ventus-3 Sport, Duo Discus and some Arcus
This brass bushing is part of the lower framework of the rudder fin on Ventus-2, Discus-2, Ventus-3 sport, all Duo Discus and Arcus (except Arcus M).
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On older gliders the diameter of the head is 14mm instead of 16mm. See bellow the suggested products.
from 1 € 7.26 incl. 19% VAT
€ 6.10 -
Oxygen-bottle holder for gliders with engine
This oxygen bottle holder is suitable for a majority of gliders equiped with a turbo or a motor.
Please choose which holder you need according to your Oxygen-bottle diameter. It is possible to adjust the holder at +/- 2 mm.
In single-seaters, one of the screws of the support is often above the spar bridge, where the wall is relatively thin. It is therefore often necessary to add the washer B40-2218 (see suggested products).
from 1 € 228.86 incl. 19% VAT
€ 192.32 -
Teflon tape roll
The 30 mm large Teflon band is self adhesive.
A roll contains 10 meters of tape.
from 1 € 23.18 incl. 19% VAT
€ 19.48 -
Wing attachment bolt for double seaters, front
The visible part of the pin is 48 mm long and has a diameter of 18 mm. The inner part is 42 mm long and has a diameter of 40 mm.
It is used on the wing roots front part of the double seaters as well as for the front and rear roots of the Janus.
from 1 € 50.28 incl. 19% VAT
€ 42.25 -
Brake pads Beringer ZEA01
These pads are used for the Beringer brakes of the Ventus-2, Discus-2, Duo Discus XL and Arcus.
We advise you to replace the pads before the thickness of friction material reachs 1.5 mm. For more information, you can consult the maintenace manual from Beringer.
A package contains the two pads used for one wheel.
from 1 € 83.30 incl. 19% VAT
€ 70.00 -
Landing gear pneumatic tension spring for Duo Discus X
This spring is 210N and it is used in the landing gear on the Duo Discus x.
This pneumatic spring is also used for the Arcus and the Duo Discus xL which have a Beringer wheel. For these planes, the spring is associated with a specific extension. You can find the full spare-part here.
An assembly jig for the tension pneumatic spring can be added as an option. If you don't have one, we advise you to buy it.
from 1 € 97.48 incl. 19% VAT
€ 81.92 -
Ignition coil for Solo 2625 from Ducati
This ignition box from Ducati is used in the Solo 2625-01 and 2625-02 but not for the "i" version. The Solo 2625-01i and 2625-02i need the ignition coil from PVL.
The cable is included.
from 1 € 598.99 incl. 19% VAT
€ 503.35 -
Nicopress-oval sleeve 1,5-2 mm
Nicopress-oval sleeve 1,5-2 mm, ref : NT281C-A or N° 28-1-C.
It is 10 x 6 x 4 mm.
from 1 € 0.30 incl. 19% VAT
€ 0.25 -
Elevator- front trim knob for Arcus, all Duo Discus and all Nimbus-4D
This is the handle for the trim of the Arcus, Duo Discus XL and Nimbus-4DL.
The roll pins are included.
Please note the pin roll can be bought separatly (see suggested product). If your glider is older than April 2015, you need to use the 2x14 mm roll pins instead of 2x16 mm.
from 1 € 62.25 incl. 19% VAT
€ 52.31 -
Eta fuse for instuments
These fuses are used for instruments.
They are available in 2, 4 and 6,3 A.
from 1 € 13.09 incl. 19% VAT
€ 11.00from 1 € 20.40 incl. 19% VAT
€ 17.14from 1 € 11.33 incl. 19% VAT
€ 9.52 -
Tailwheel tube 200x50 with 90° valve
This tube is for all 200x50 mm tailwheels and it is adapted to a large majority of modern Schempp-Hirth gliders.
from 1 € 10.60 incl. 19% VAT
€ 8.91 -
Landing gear guide plate for singel seater
This plate in grey PVC is used as a guide for all single-seater landing gear (except for the Ventus-3).
Its length is 220 x 24 mm and there is no hole. Adjust it to your glider.
from 1 € 6.47 incl. 19% VAT
€ 5.44 -
Oxygen-bottle neck-holder
This oxygen bottle support is suitable for a majority of Schempp-Hirth gliders.
Please choose the diameter of your oxygen bottle. If your bottle has a diameter that is not in the list, please contact Schempp-Hirth spare part.
Please note that for some bottle (like the "Montain High"), you will need an extender to shift the pressure gauge away from the bottle neck.
from 1 € 214.20 incl. 19% VAT
€ 180.00from 1 € 214.20 incl. 19% VAT
€ 180.00 -
Turbulator tape 0,8x5 for almost all gliders (Roll)
This turbulator band (or Noppenband) is 10 mm large and self-adhesive . The dimples are 0,8 mm high and they are distanced by 5 mm.
It is very often used on Schempp-Hirth glider but look at your sealing instructions as some gliders, like the Arcus and the Ventus 3, are using a different turbulator tapes.
The roll is 10 metres long.
from 1 € 35.99 incl. 19% VAT
€ 30.24 -
Airbrake drive funnel
This drive funnel is used on almost all Schempp-Hirth gliders except the Nimbus-4 and the Ventus-3.
Two lock nuts M 6-8, DIN 985 and a lock nut M6 TRELOC, DIN 439 are included. However, your glider has a specific set of distance washer that are not provided. Please before disassemble the funnel make sure you know which washer go where.
On the Ventus-2 and Discus-2c, you may also need a set of screws that can be baught as an option.
from 1 € 370.99 incl. 19% VAT
€ 311.76 -
Main brake cylinder for Ventus-2 and Discus-2 using the disc brakes type Magura (Option)
This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST and with a “Magura” cylinder brake.from 1 € 375.87 incl. 19% VAT
€ 315.86 -
Main wheel axle
This is the axle for the main landing gear of almost all Discus, Discus-2, Ventus-2 and Ventus-3.
It is 215 mm long, including a M12x1,5 head (4 mm long) and a M12 screw thread (12 mm long).
Careful: some Ventus c, Ventus-2a, Ventus-2b and Discus-2b with carbon fiber undercarriage need another axle . If you are not sure, measure the axle that is currently used or contact Schempp-Hirth spare part.
You may also want to buy the 8 mm M12x1,5 castle nut which is used to secured the axle (See suggested products).
from 1 € 70.50 incl. 19% VAT
€ 59.24 -
Ignition coil for Solo 2625 type "i" from PVL
The ignition box from PVL is used for the Solo 2625-01i and 2625-02i but not for the other version. The Solo 2625-01 and 2625-02 need the ignition coil from Ducati.from 1 € 207.30 incl. 19% VAT
€ 174.20 -
Nicopress-Stop sleeve 1,5-1,7mm
Nicopress-Stop sleeve 1,5-1,7mm, NTS011C (round).
It is 5 x 5 x 5 mm.from 1 € 0.48 incl. 19% VAT
€ 0.40 -
elevator-trim blade spring for Arcus, all Duo Discus, all Nimbus-4D and all Discus
This spring is used for the trim of the Arcus, Duo Discus XL, Nimbus-4DL and all the Discus from the Discus a to the Discus-2c.
It is 25mm lage and the legs are 40mm long. The central part is 12,5mm.
Some glider need roll pins. They are not included but they can be baught individaly (see the suggested products).
from 1 € 4.65 incl. 19% VAT
€ 3.91 -
Coolant temperature sensor for Solo 2625 01 and 02
This sensor is used in the Solo 2625 01 and 2625 02 to measure the water temperature.
The sensor used on the Arcus M and Ventus-3M (Solo 2625 01i and 02i) is different. You can find it on the suggested products.
from 1 € 147.80 incl. 19% VAT
€ 124.20 -
Brass bushing for the lower rudder framework fin of the Ventus a, b, and c and Discus a and b
This brass bushing is part of the lower framework of the rudder fin on Ventus a, b and c, and the Discus a and b.
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On more modern gliders the diameter of the head is 16 mm instead of 14 mm. You cannot use one for the other.
from 1 € 8.03 incl. 19% VAT
€ 6.75 -
Tesafix roll 9 and 12 mm
This double side tape (Tesafix 4965) is used for control surface sealing and is available in 2 different widths: 9 or 12 mm.
A roll contains 50 meters of tape.
from 1 € 20.15 incl. 19% VAT
€ 16.93from 1 € 20.74 incl. 19% VAT
€ 17.43from 1 € 28.02 incl. 19% VAT
€ 23.55 -
Shim washer kit for 18 mm wing bolt
These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.
They fit a 18 mm wing bolt. That includes the front and back bolts at the wing root of the double seaters.
These washers internal diameter is 17,8 mm. They are a bit smaller than the pin in order to stay in place when installed.
from 1 € 48.27 incl. 19% VAT
€ 40.56 -
Brake pads for Cleveland caliper 30-9
These brake lining (Tost p/n 075865) are used on brake assembly 30-9.
It can be mounted to 4′′, 5′′ and 6′′ disk brake wheels of the series Penta, Tria and Classic and on the original Cleveland brakes- wheel system.
Different system has been used and several TN have been approved. Please look carefully to your brakes and order similar brake pad.
from 1 € 72.08 incl. 19% VAT
€ 60.57 -
Main wheel axle castle nut, M12
This is the castle nut is used for the main landing gear of almost all Discus, Discus-2, Ventus-2 as well as the Ventus-3.
It is 8 mm, M12 x 1,5 DIN 937.
from 1 € 12.91 incl. 19% VAT
€ 10.85 -
Exhaust gasket for Solo 2625
Gasket exhaust is used for the SOLO engines 2625.
It is 68,5 x 48 x 2 mm.
It is sold by the unit.
from 1 € 25.87 incl. 19% VAT
€ 21.74 -
Nicopress-Stop sleeve 2,5 mm
Nicopress-Stop sleeve 2,5 mm, NTG282G-100.
It is 10 x 9 x 6 mm.
from 1 € 0.67 incl. 19% VAT
€ 0.56 -
Safety ring-spring steel, DIN471, size 8
This safety ring-spring steel, DIN471, size 8 is used to secure the Lindner wingtip wheel axle.from 1 € 0.55 incl. 19% VAT
€ 0.46 -
Roll pin for trim
Roll pin DIN 1481 / ISO 8752 stainless.
They are (mainly) used to in trim of the Arcus, Duo Discus XL and Nimbus-4DL.
There is two models : On gliders produced after April 2015, you will probably need the 2 x 16 mm model. For the older glider you will need to use the 2x14 mm roll pins. Please have a look in your glider to confirm which models you need.
from 1 € 0.36 incl. 19% VAT
€ 0.30 -
Coolant temperature sensor for Solo 2625 01i and 02i
This sensor is used in the Solo 2625 01i and 2625 02i engines to measure water temperature.
Please note that the sensor used in the older Solo 2625 model is different. You can find it under the suggested products.from 1 € 77.43 incl. 19% VAT
€ 65.07 -
Kit for rudder pedal adjustment
This kit contains all you need to replace the pedal adjustment mechanism, including the instructions.
It is made for the Ventus b, Ventus c, Ventus-2, Discus, Discus-2, Nimbus-4, Duo Discus and the Arcus.
On the Nimbus-4, the Ventus, the Discus and the Duo Discus the mecanisme included a spring. It is now replace by a gummi band. With this kit, you can upgrade the old sytem to the newest one.
from 1 € 56.66 incl. 19% VAT
€ 47.61 -
Shim washer kit for 14 mm wing bolt
These washers are used to adapt the distance of the wing to the fuselage. The kit contains eight 0,5 mm thick washers and four 0,8 mm thick washers.
They fit a 14 mm wing bolt. That includes the front and back bolts at the wing root of almost all the single seaters as well as the wing extention bolt of the Discus-2c, Ventus-2c and Ventus-3 and some winglet bolts.
These washers internal diameter is 13,8 mm. They are a bit smaller than the pin in order to stay in place when installed.
from 1 € 26.99 incl. 19% VAT
€ 22.68 -
Hydraulic fitting straight connection for Magura system
This connection fitting (Tost p/n 075830) is in aluminium, with standard screwing JIC04 .
This system is used for the Ventus-2c, Discus-2b and Duo Discus which are using the 5" Classic wheel from TOST with a Magura cylinder brake.
from 1 € 7.97 incl. 19% VAT
€ 6.70 -
Tube 5.00-5 (and 6.00), TR67
This tube fits 5.00 and 6.00 tyres.
Its long valve is adapted for the double seaters, except if they have a TOST Penta wheel.
It is also used for the single seater with a 5" wheel equiped with a TOST drum brakes like the Kobold 5".
You can find the tube 5.00-5, TR87, with a sort valve, in the suggested products.
This item is discontinued until further notice. We are sorry for the inconvenience.
from 1 € 325.57 incl. 19% VAT
€ 273.59 -
Spark plug B7HS
This spark plug is used for all SOLO engines.from 1 € 10.31 incl. 19% VAT
€ 8.66 -
Nicopress-Stop sleeve 3,0-3,5 mm
Nicopress-Stop sleeve 3,0-3,5 mm, NT283M / n° 28-3-M.
It is 14 x 12 x 8 mm.
from 1 € 1.04 incl. 19% VAT
€ 0.87 -
Turbulator tape 0,85x16 (roll)
This turbulator band (or Noppenband) is 10 mm large. The dimples are 0,85 mm high and they are distanced by 16 mm.
This model is mainly used for the Arcus and the Ventus-3. Look at your sealing instructions for more information.
A roll is 10 meters.
from 1 € 3.42 incl. 19% VAT
€ 2.87 -
Front canopy hinge for Arcus, Duo Discus xL and Nimbus-4DL
This hinge is for the canopy of all Arcus, Duo Discus xL and Nimbus-4DL.
This front hinge is printed in 3D and will break in case of evacuation. If it happens accidentally, it is possible to replace it. This hinge was previously in carbon fiber but you can replace it by that one with minor adjustments.
Note: the hinge at the back is different.
from 1 € 92.32 incl. 19% VAT
€ 77.58 -
Rod end bearing 14c6, M8x58
Rod end bearing with a 14c6 head and M8 x 58 length body.
Other rod end bearings are used in our gliders. If you are not sure which one you need. Please contact the Spare Part team.
from 1 € 17.41 incl. 19% VAT
€ 14.63 -
Green ball knob for trim
This handle for the trim is a format 25 mm, M6. It is made in aluminium and green powdered.
from 1 € 18.34 incl. 19% VAT
€ 15.41 -
Rotule L'Hotellier MS 961-150-150-L3
This l'Hotellier ball end is used for gliders with manual control hookups.
For some gliders, including the Cirrus, you need a washer and a locknut. They are included in the package.
The EASA Form 1 is included when needed.
from 1 € 156.34 incl. 19% VAT
€ 131.38 -
Hollow screw MS 4 for Magura system
This screw is used for the Ventus-2c with a 5" Classic wheels from TOST and a Magura cylinder brake.
It is 25 mm long and the head size is 14 mm.
from 1 € 1.55 incl. 19% VAT
€ 1.30 -
Tube 5.00-5 (and 6.00), TR87
This tube fits 5.00 and 6.00 tyres.
Its short valve is adapted for almost all single seater with a 5" wheel (except the one equipped with TOST drum brakes like the Kobold 5"). It is also used for the double seaters equipped with a TOST Penta wheel.
You can find the tube 5.00-5, TR67, with a long valve, in the suggested products.
from 1 € 159.34 incl. 19% VAT
€ 133.90 -
Cooling water gasket for the cylinder head of SOLO 2625
This sealing is used for the cooling system on the cylinder head of all SOLO 2625 engines.
It is 51 x 32 x 1,5 mm.
Older 2625 engines need another type of filter. If the filter you want to replace doesn't look like that one and is not in metal, contact Schempp-Hirth spare-part service.
from 1 € 8.37 incl. 19% VAT
€ 7.03 -
Thimble 2,5 mm galvanized
Thimble 2,5 mm galvanized.
It is 27 x 15 x 5 mm.
from 1 € 0.24 incl. 19% VAT
€ 0.20 -
Turbulator tape 0,85x10 (per meter)
This turbulator band (or Noppenband) is 10 mm large. The dimples are 0,85 mm high and they are distanced by 10 mm.
This model is mainly used for the Ventus-3. Look at your sealing instructions for more information.
It is sold by the meter.
from 1 € 6.09 incl. 19% VAT
€ 5.12
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.