Spare parts
-
Bush for the rear spindle suspension of almost all the M
This bushing is Ø13x1,5x34,5.
It is used for the rear spindle suspension of des Arcus M, Nimbus-4DM, Ventus-3M und Ventus-2cM
from 1 € 7.82 incl. 19% VAT
€ 6.57 -
Magnet for Ventus-2c, Discus-c and Double seater canopy closing mecanism
from 1 € 7.83 incl. 19% VAT
€ 6.58 -
Hydraulic fitting straight connection for Magura system
This connection fitting (Tost p/n 075830) is in aluminium, with standard screwing JIC04 .
This system is used for the Ventus-2c, Discus-2b and Duo Discus which are using the 5" Classic wheel from TOST with a Magura cylinder brake.
from 1 € 7.97 incl. 19% VAT
€ 6.70 -
O-Ring for wing wheel Lindner of the Duo Discus, Discus and the Ventus, Ø60
This gummi ring is Ø60 x Ø10 and is the tire of the wing wheel Lindner of the Duo Discus, Discus and the Ventus.
It is sold by the unit.
from 1 € 7.97 incl. 19% VAT
€ 6.70 -
Brass bushing for the lower rudder framework fin of the Ventus a, b, and c and Discus a and b
This brass bushing is part of the lower framework of the rudder fin on Ventus a, b and c, and the Discus a and b.
Careful: on rare cases, gliders need a slightly larger head: 2 mm instead of 1 mm (see picture). Please look carefully at your actual part to buy the same model. If you need the 2 mm version, please contact us.
On more modern gliders the diameter of the head is 16 mm instead of 14 mm. You cannot use one for the other.
from 1 € 8.03 incl. 19% VAT
€ 6.75 -
Plastic finger for propeller stopper for the Ventus-3M and Arcus M edition 2020
This stopper is used for the propellor of the Ventus-3M and the Arcus M edition 2020.
Its stopnut is included.
from 1 € 8.06 incl. 19% VAT
€ 6.77 -
Distance washer for mainwheel
This washer is 14 x 2 x 32 mm and it is used for the main wheel of almost all Schempp-Hirth gliders.from 1 € 8.10 incl. 19% VAT
€ 6.81 -
Water filler cap sealing for Ventus-3
This sealing is made for the Ventus-3 sealing caps.
Its diameter is 26 mm and the sealing is 4,0mm thick.
from 1 € 8.19 incl. 19% VAT
€ 6.88 -
Filter WK 21 for pitot
This WK 21 filter is used for the pitot tube in the glider’s nose.from 1 € 8.19 incl. 19% VAT
€ 6.88 -
Brass Bushing for Standard Cirrus elevator support
This brass bushing (13x1.5x6.5 mm) is used on the front elevator mount of the Standard Cirrus.
from 1 € 8.26 incl. 19% VAT
€ 6.94 -
Cooling water gasket for the cylinder head of SOLO 2625
This sealing is used for the cooling system on the cylinder head of all SOLO 2625 engines.
It is 51 x 32 x 1,5 mm.
Older 2625 engines need another type of filter. If the filter you want to replace doesn't look like that one and is not in metal, contact Schempp-Hirth spare-part service.
from 1 € 8.37 incl. 19% VAT
€ 7.03 -
Steel bushing for rudder cable
This steel bushing, 8x1x7 mm without hole, is used for rudder cables.
They are sold individually.
The screw (05018 LN 9037, Ref L01-0005), washer (M05 DIN 125, Ref L01-0228) and lock nut (M 5-8, DIN 985 vz, Ref L01-0703) are provided.
The EASA form one is included.
from 1 € 8.45 incl. 19% VAT
€ 7.10 -
Rubber buffer 20x25, M6x18 for the radiator of the Ventus-2cM and Nimbus-4DM.
This silent block is used for the cooler of the Ventus-2cM, Nimbus-4DM and Arcus M engine.
The head is 25 mm and the screw 18 mm. Its diameter is 20 mm.
Look at the model(s) that you want to replace and order the same. According to your glider, you might also want this rubber buffer.
from 1 € 9.21 incl. 19% VAT
€ 7.74 -
Water filler cap top
This plug is 5 mm high and its diameter is 36 mm. It fit all the Ventus 2, Discus 2, Nimbus 3, Duo Discus and the first Arcus.
Dependant on the glider, older Ventus and Discus can need this model or a 35 mm diameter sealing cap that is 7,5 mm high. Please look at your current model to order the same. If you need the thick sealing cap, you can order it through Schempp-Hirth spare-part form.
For a clean fit, the cover should be adjusted by grinding the profile contour.
from 1 € 9.64 incl. 19% VAT
€ 8.10 -
Control cable B 3.2 mm
Control cable B, 3.2 mm, ISO 2020 (1/8”), DIN 3051 compliant, 7x19 construction.
Sold by the meter.
This cable is commonly used for rudder control. Please refer to your maintenance manual to confirm the correct cable type and connection method.
It is also used for the pylon arresting wires on the Nimbus-4M, Nimbus-4DM, Ventus-2cM, and Arcus M.
For this application, we recommend purchasing the "Kit pylon arresting wire for V2cM, N4M, N4DM and AM".from 1 € 10.02 incl. 19% VAT
€ 8.42 -
Flap handle for some Ventus-2c and the Ventus-3
from 1 € 10.04 incl. 19% VAT
€ 8.44 -
Copper mesh wire tube
This braided hose is KAG 3,11 QMM VSN 36 x 11 x 0,10.
It is used with the transparent hose NW 4,8x1,6 (T20-0064485) for the fuel sytem of almost all Turbo, the Ventus-2cM and the Nimbus-4DM.
It is sold by the meter.
Be aware that for Turbo gliders another mesh wire tube KAG 1,32 QMM 24x7x0,1 (ref: L07-0319) is used at the level of the T-connection.
from 1 € 10.25 incl. 19% VAT
€ 8.61 -
Spark plug B7HS
This spark plug is used for all SOLO engines.from 1 € 10.31 incl. 19% VAT
€ 8.66 -
Tailwheel tube 200x50 with 90° valve
This tube is for all 200x50 mm tailwheels and it is adapted to a large majority of modern Schempp-Hirth gliders.
from 1 € 10.60 incl. 19% VAT
€ 8.91 -
Gasket for canopy frame of the Double Seaters
This gasket is used for the canopy of the Duo Discus and the Arcus.
It is sold by the meter.
from 1 € 10.60 incl. 19% VAT
€ 8.91 -
Rod end bearing KA-6-DC2, M8x50
Rod end bearing with a KA-6-DC2 head (askubal) and M8 x 50 length body.
Other rod end bearings are used in our gliders. If you are not sure which one you need. Please contact the Spare Part team.
from 1 € 11.59 incl. 19% VAT
€ 9.74 -
Hexagon screw 06021,5 , LN 9037
This 6k-Screw is used for the airbrake drive funnel of the Ventus-2c and Discus-2c.from 1 € 11.80 incl. 19% VAT
€ 9.92 -
Safety springs for L'Hotellier
Pair of safety springs to secure l'hotellier connectors for gliders with manual control hookups.
The EASA Form 1 is included when needed.
from 1 € 11.90 incl. 19% VAT
€ 10.00 -
Main wheel axle castle nut, M12
This is the castle nut is used for the main landing gear of almost all Discus, Discus-2, Ventus-2 as well as the Ventus-3.
It is 8 mm, M12 x 1,5 DIN 937.
from 1 € 12.91 incl. 19% VAT
€ 10.85 -
Eta fuse for instuments
These fuses are used for instruments.
They are available in 2, 4 and 6,3 A.
from 1 € 13.09 incl. 19% VAT
€ 11.00from 1 € 20.40 incl. 19% VAT
€ 17.14from 1 € 11.33 incl. 19% VAT
€ 9.52 -
Foam sealing
from 1 € 13.09 incl. 19% VAT
€ 11.00 -
Tesa foam for horiz. tailplane sealing
This sealing is critical to limit the ageing of the horizontal tailplane fixation mechanisms. We advise you to renew it every couple of years.
Description: Tesa foam 9 x 4 mm, 10 m by roll.
For a simple installation, you can instead buy premade form that can be easily adapted to single seater and double seater.
from 1 € 13.16 incl. 19% VAT
€ 11.06 -
Landing gear guide plate for Duo Discus xL and Arcus
This grey PVC plate is used as a guide for the Duo DiscusxL and xLT and Arcus.
Dimensions: 233×25 mm.
Please note: the model used for the Duo Discus and Nimbus-4D is shorter (ref. B40-3305). You can find it in the suggested products below.
from 1 € 13.47 incl. 19% VAT
€ 11.32 -
Single seater horiz. tailplane sealing for Ventus-3 Sport
This sealing is critical to limit the ageing of the horizontal tailplane fixation mechanisms. We advise you to renew it every couple of years.
The form is 94,98 x 370,00 mm. It is designed for the Discus-2a, -2b and the Ventus-3 Sport. It may also be possible to adapt it for older gliders. If you prefer, you can make the form yourself using a Tesa Foam roll.
from 1 € 13.52 incl. 19% VAT
€ 11.36 -
Brake pull cable for single seaters with magura type disc
This system is used for the Ventus-2 and the Discus-2 which are using the 5" Cleveland wheel from TOST, with a “Magura” cylinder brake.
The brake cable measures 555 mm in length and features a 6 x 10 mm nipple.
from 1 € 13.96 incl. 19% VAT
€ 11.73 -
Leg springs for water dump system for Arcus, Duo Discus XL and Ventus-2cx
This pair of leg springs is used for the Arcus, Duo Discus xL and Ventus-2cx.
Each spring is 101,5 mm long and 21 mm large.
from 1 € 14.04 incl. 19% VAT
€ 11.80 -
Eyelet at landing gear doors for all models
These eyelet is used for the landing gear doors for all models.from 1 € 14.29 incl. 19% VAT
€ 12.01 -
Main wheel axle castle nut, M14 for double seaters
This is the castle nut is used for the main landing gear of all the Duo Discus and Arcus.
It is 8 mm, M14 x 1,5 DIN 937.
from 1 € 15.16 incl. 19% VAT
€ 12.74 -
Double seater horiz. tailplane sealing
This sealing is critical to limit the ageing of the horizontal tailplane fixation mechanisms. We advise you to renew it every couple of years.
The form is 98,80 x 435,00 mm. It is designed for the Duo Discus and the Arcus horizontal tailplanes. It may also be possible to adapt it for older gliders. If you prefer, you can make the form yourself from a Tesa Foam roll.
from 1 € 15.51 incl. 19% VAT
€ 13.03 -
Rod end bearing 10c6 M8x58
Rod end bearing with a 10c6 head and M8x58 length body.
Other rod end bearings are used in our gliders. If you are not sure which one you need. Please contact the Spare Part team.
from 1 € 15.90 incl. 19% VAT
€ 13.36 -
Decompression retraction sheet, for SOLO 2350 old version
This part is 148 x 20 x 2 mm.
It is used for the old Nimbus-4T and single seater designed before 2000: The Discus-2T (SN<41), the Discus-2cT (SN<36) and the Ventus-2cT (SN<185).
Some of these gliders might have been modified. The new retraction sheet looks different, so look carefully at the picture to order the same that you have on your glider.
You can find the newer one here.
It is sold with its brass bushings, 8x1x2,5 mm.
from 1 € 15.98 incl. 19% VAT
€ 13.43 -
Tension spring for double seater trim rear system.
It is used in the trim system of the Arcus, Duo Discus, Nimbus-4, and Nimbus-4D gliders, in the rear position, with two springs installed per glider.from 1 € 16.02 incl. 19% VAT
€ 13.46 -
Ring buffer for SOLO 2350
SOLO Silent block bush, spare part n° 00 94 240
It is 14 mm large and its diameter is 37 mm.
from 1 € 16.30 incl. 19% VAT
€ 13.70 -
Single seater horiz. tailplane sealing for all Discus-2, Ventus-2 and the Ventus-3 performance
This sealing is critical to limit the ageing of the horizontal tailplane fixation mechanisms. We advise you to renew it every couple of years.
The form is 94,98 x 370,00 mm. It is designed for the Discus, Ventus-2c and Ventus-3 Performance. It may also be possible to adapt it for older gliders. If you prefer, you can make the form yourself using a Tesa Foam roll.
from 1 € 16.77 incl. 19% VAT
€ 14.09 -
Perspex disc 53,5 mm with 5 mm hole
This perspex disc is made for the Ventus-2a.
Its diameter is 53,5 mm and the central hole is 5 mm.
from 1 € 16.79 incl. 19% VAT
€ 14.11 -
spherical bearing GL 18
This spherical bearing is adapted for 18mm diameter pin of the double seaters.
The internal diameter is 18 mm and the part is 32x32x14 mm.
from 1 € 17.06 incl. 19% VAT
€ 14.34 -
Rod end bearing 14c6, M8x58
Rod end bearing with a 14c6 head and M8 x 58 length body.
Other rod end bearings are used in our gliders. If you are not sure which one you need. Please contact the Spare Part team.
from 1 € 17.41 incl. 19% VAT
€ 14.63 -
Distance washer for tailwheel
This washer is 16 x 2 x 4,5 mm and it is used for the tail wheel
from 1 € 17.62 incl. 19% VAT
€ 14.81 -
Distance washer for tailwheel
This washer is 16 x 2 x 5,5 mm and it is used for the tail wheel.from 1 € 17.62 incl. 19% VAT
€ 14.81 -
Radachse für Lindner Flügelrad für Arcus and Ventus-2c
This wingtip wheel axle is used for the Arcus and Ventus-2c.
The safety ring spring can be found in the suggested products below.
from 1 € 17.67 incl. 19% VAT
€ 14.85 -
![BWS-2009_Feder_für_Flexiputzer,_lo_ru[1].jpg](/uploads/tx_aimeos/1.d/preview/d/d/dd8babc5_bws-2009_feder_fur_flexiputzer-_lo_ru-1.webp?v=20240429103959)
BWS springs for Flexiwiper
These replacement springs are specifically designed for use with the BWS Flexiwiper system. Each set is sold as a matched pair, for the left and right Flexiwiper unit.
Important compatibility note:
These springs are not compatible with the Ventus-3 or Arcus edition 2020 Garagewipers models.from 1 € 17.85 incl. 19% VAT
€ 15.00 -
![BWS-2009_Feder_für_Flexiputzer,_lo_ru[1].jpg](/uploads/tx_aimeos/1.d/product/7/0/70ab0db5_.webp?v=20251219103813)
BWS springs for Flexiwiper in a garage
These replacement springs are specifically designed for use with the BWS Garagewiper system. Each set is sold as a matched pair for the left and right wiper units.
Important compatibility note:
These springs are not compatible with the classic Flexiwiper model.from 1 € 17.85 incl. 19% VAT
€ 15.00 -
Special screw for Arcus M and Ventus-3M tailwheel axle
This M8 screw is design for the steering tail wheel axle of the Arcus-M and the Ventus-3M.
from 1 € 17.87 incl. 19% VAT
€ 15.02 -
Bellows V6-905 for the fin tank
This rubber boot ensures the sealing of the tail ballast of most of the Schempp-Hirth gliders.
It is advisable to replace it every 2-3 years to avoid water leaks.Its dimensions are 72 x 38 mm.
from 1 € 18.31 incl. 19% VAT
€ 15.39 -
Green ball knob for trim
This handle for the trim is a format 25 mm, M6. It is made in aluminium and green powdered.
from 1 € 18.34 incl. 19% VAT
€ 15.41 -
Flat spring for Janus, Nimbus-2, -3D, -4D flap drive
This tension spring is used to maintain the flap handle on the right position.
On the Janus B and Nimbus-2, it is located near the front seat handle.
Originally, the Janus C, the Nimbus-3D and the Nimbus-4D are using another spring that looks very different (ref B40-2417) and that is located on the back seat cockpit wall. However some gliders have been modified and they are now using this flat spring but near the spar bridge.
The other reference is available below under the suggested products.
from 1 € 18.64 incl. 19% VAT
€ 15.66
Help, my spare part is not yet in the shop!
If you cannot find the item you want please use the spare-part form and we will come back to you shortly.